BLAUBERG Ventilatoren Box-S User Manual Download Page 3

www.blaubergventilatoren.de

Box-s

3

THE PRODUCT MUST BE DISPOSED SEPARATELY AT THE END OF ITS SERVICE LIFE.

DO NOT DISPOSE THE UNIT AS UNSORTED DOMESTIC  WASTE.

UNIT INSTALLATION AND OPERATION SAFETY PRECAUTIONS

•  Disconnect the unit from power mains prior to any installation operations.
•  Unpack the unit with care.
•  The unit must be grounded!
•  While installing the unit, follow the safety regulations specific to the use of electric tools.
•  Do not change the power cable length at your own discretion. 
•  Do not bend the power cable. 
•  Avoid damaging the power cable. 
•  Do not put any foreign objects on the power cable.
•  Do not lay the power cable of the unit in close proximity to heating equipment.
•  Do not use damaged equipment or cables when connecting the unit to power mains.
•  Do not operate the unit outside the temperature range stated in the user’s manual. 
•  Do not operate the unit in aggressive or explosive environments.
•  Do not touch the unit controls with wet hands. 
•  Do not carry out the installation and maintenance operations with wet hands.
•  Do not wash the unit with water. 
•  Protect the electric parts of the unit against ingress of water. 
•  Do not allow children to operate the unit.
•  The unit is allowed to be used by children aged from 8 years oldand above and persons with 

reduced physical, sensory, or mental capabilities or no experience and knowledge provided 
that they have been given supervision or instruction regarding safe use of the unit and 
understand the risks involved.

•  Disconnect the unit from power mains prior to any technical  maintenance.
•  Do not store any explosive or highly flammable substances in close proximity to the unit.
•  When the unit generates unusual sounds, odour, or emits smoke, disconnect it from power 

supply and contact the Seller.

•  Do not open the unit during operation.
•  Do not direct the air flow produced by the unit towards open flame or ignition sources.
•  Do not block the air duct when the unit is switched on.
•  In case of continuous operation of the unit, periodically check the security of mounting.
•  Do not sit on the unit and avoid placing foreign objects on it.
•  Use the unit only for its intended purpose.

Summary of Contents for Box-S

















Reviews: