Blata Minibike 2.5 User Manual Download Page 5

 

 

 
 

INTRODUCTION 

Minibike  2,5 is intended for a drive on closed tracks with even, smooth, and 
dust-free surface. Both growns - up and children can ride on the Minibike. 
Children only under the supervision of a grown - up and responsible person. If 
the terms of a track are fulfilled, the Minibikes can be used for races. Minibike 
Blata should not be used during winter season and under bad weather 
conditions. Usage under these conditions leads to abnormal mechanical wear 
and corrosion of most minibike parts - especially those directly exposed to 
climatic influences. Beside that, riding under these conditions increase the 
risk of injury or health damage. 
Minibike is equipped with a single - cylinder, two - stroke, petrol combustion 
engine, with a front and rear disc brake, the rear one being controlled by a 
lever on the left side of handlebars and the front one by a lever on the right 
side of handlebars, when seeing in the ride direction. The fuel quantity 
controlled by a handle on the right side of handlebars. The engine is fitted with 
an air filter and a exhaust silencer. The driving moment transmission from 
engine to the driven rear wheel is carried out by a chain drive the ratio of 
which can by changed to a small extend by a sprocket wheel exchange on the 
rear wheel. 

 

BASIC TECHNICAL DATA 

 

ENGINE: 

TWO - STROKE ...............................................................AIR COOLED 

 CILINDER 

CAPACITY............................................................. 39,9 ccm 

 POWER 

OUTPUT.................................................. 2,5 kW at 8 700 rpm 

 TORGUE 

..............................................................3,5 Nm at 6 000 rpm 

 CARBURETOR 

.................................................................DELL’ORTO 

 IGNITION......................................................................... ELECTRONIC 
 STARTING ..............................................................................MANUAL 
 CLUTCH .....................................................CENTRIFUGAL, FRICTION 
FRAME: WELDED .................................OF HIGH - STRENGTH STEEL TUBES 
LINING: .................................................................................... THREE PARTED 
BRAKES: FRONT 

WHEEL.....................................MECHANICAL DISC BRAKES 

 REAR 

WHEEL.......................................MECHANICAL DISC BRAKES 

WHEELS: FRONT 

WHEEL............................................ OF LIGHT ALLOY 4” - 51 

 REAR 

WHEEL.............................................. OF LIGHT ALLOY 4” - 95 

TIRES: FRONT ......................................................... 3,00 - 4” WITH PATTERN 
 REAR............................................................ 3,00 

- 4” WITH PATTERN 

TUBES: FRONT 

REAR ....................................................................... 3,00 - 4” 

FUEL: 

......... MIXTURE OF PETROL 91 OR HIGHER OCTANE  + 2-STROKE  

 SYNTHETIC 

OIL 

 MIXING 

RATIO.............................................................................. 50 : 1 

 TANK 

CAPACITY......................................................................1 LITRE 

HIGHEST VELOCITY IN ACCORDANCE 
WITH THE INSTALED RATIO:........................................... up to 28 mph ( 45 km/ h) 
UNLOADED WEIGHT..........................................................................37,5 lb ( 17 kg) 
CARRYING CAPACITY.....................................................................242 lb ( 110 kg ) 
BASIC DIMENSIONS: 
 LENGHT ........................................................................36,2” (920 mm) 
 WIDTH ..............................................................................20” (500 mm) 
 HEIGHT ...........................................................................20 ” (500 mm) 

2

Summary of Contents for Minibike 2.5

















Reviews: