background image

BL-183 / BL-233 SANDER/POLISHER 

SECTION 4 

ADDITIONAL SAFETY RULES 

 

INSTRUCTION MANUAL

OCTOBER 2008

 
 
The Operating Instructions must be 

supplemented

 by other 

instructions

; this 

includes the duty to 

supervise

 and 

report

 incidents relating to 

particular  

 
working practices

, for example, work organization, work procedures and 

personnel allocation. 
 
Personnel entrusted with working with the machine must read the 

Operating 

Instructions

 before starting work, in particular all safety instructions. To read 

these instructions after work has commenced is too late. This particularly applies 
to incidental activities such as setting up the equipment, carrying out 
maintenance work or training staff to work with the machine. 
 
From time to time the working practices of the operators are to be checked by a 
supervisor, especially as to the items regarding awareness of 

safety and 

hazards

  

Personnel must tie back long hair, and not wear loose clothing or jewelry 
including rings. There is a risk of injury through items getting caught or being 
drawn into moving machinery. 
 
 

 

 
 
 
 
 

All 

safety and hazard notices

 at or on the machine must be kept complete and 

legible

 
If 

safety-critical changes

 occur to the machine or its working method, the 

machine must be 

shut down immediately

! The cause of the fault must be 

established and remedied immediately! 
 

 

  

 

 
 

 

This applies in particular to the fitting and adjustment of safety devices as well as 
to welding on load-bearing parts. 
 
Spare parts must comply with the technical requirements specified by the 
manufacturer. This is always guaranteed if original spare parts are used. 
 

Use 

personnel protection equipment

 if necessary or required by 

local regulations! Take notice of 

all 

safety and hazard notices on 

the machine! 

Changes

, add-ons or conversions to the machine which might 

impair safety, must not be made, without 

the manufacturer’s 

permission! 

Summary of Contents for BL-183


























Reviews: