USE AND MAINTENANCE
• It is recommended to operate the appliance prior to cooking. It is recommended to leave the appliance in
operation for 15 minutes after cooking is terminated in order to help eliminate cooking vapors and odors. The
proper function of the rangehood is conditioned by the regularity of the maintenance operations, in particular,
the active carbon filter.
• The anti-grease filters capture the grease particles suspended in the air, and are therefore subject to clogging
according to the frequency of the use of the appliance. In order to prevent fire hazard, it is recommendable to
clean the filter at a maximum of 2 months by carrying out the following instructions:
- Remove the filters from the rangehood and wash them in a solution of water and neutral liquid detergent,
leaving to soak.
- Rinse thoroughly with warm water and leave to dry.
- The filters may also be washed in the dishwasher. The aluminum panels may alter in colour after several washes.
This is not cause for customer complaint nor replacement of panels.
• The active carbon filters help to purify the air that is replaced in the environment. The filters are not washable
nor reusable and must be replaced at maximum every four months. The saturation of the active carbon filter
depends on the frequency of use of the appliance, by the type of cooking and the regularity of cleaning the
anti-grease filters.
• The light function is designed for use during cooking and not for prolonged general illumination of the envi-
ronment. Prolonged use will notably reduce the duration of the bulb.
• Light replacement - halogen (Fig.7)
12 volt 20 W Halogen.
Remove the glass retaining ring and glass.
Replace the globe with another of the same type.
Replace the glass and retaining ring.
• Controls (Fig.8)
Push-button A
= On/off lights switch.
Push-button B
= On/off rangehood switch.
The appliance switches on at speed level 1, If the rangehood is on depress the push-button for 2 sec. to switch
off the rangehood.
If the rangehood is at speed level 1 it will not be necessary to depress the push-button to switch the rangehood
off. Decreases the motor speed.
Display C
= Indicates the motor speed level selected and activates the timer.
Push-button D
= Switches on the rangehood. Increases the motor speed.
Touching the key at 3rd speed, the intensive function runs for 10 minutes, then the appliance will go back to
work at the original speed. During this function the display blinks.
Key E
= By pressing Key
E
, the motor will continue to run for 15 minutes at the selected speed and will automatically
turn off after 15 minutes. The Timer is deactivated by re-pressing Key
E
. When the Timer is activated the decimal
point must flash on the display. The Timer cannot be activated if the intensive speed is functioning.
The
“clean air”
function is activated by pressing key
E
for 2 seconds when the appliance is switched off. This
switches the motor on for 10 minutes every hour at the first speed. During functioning a rotary movement of
the peripheral segments must be visualised on the display. When this time has passed the motor switches off
and the fixed letter “
C
” must be visualised on the display until the motor re-starts after 50 minutes for another
10 minutes and so on. Press any key apart from the light keys to return to normal functioning. Press key
E
to
deactivate the function.
• Active carbon/grease filter saturation:
- When display item
C
flashes, at a speed where it alternates with the letter
F
(e.g. 1 and F), the grease filters must
be washed.
- When display item
C
flashes, at a speed where it alternates with the letter
A
(e.g. 1 and A), the carbon filters
must be replaced.
After the clean filter has been positioned correctly, the electronic memory must be reset by pressing button
A
for approximately 5 seconds, until the indication
F
or
T
shown on the display
C
stops flashing.
THE MANUFACTURER DECLINES ALL RESPONSIBILITY FOR EVENTUAL DAMAGES CAUSED BY BREACHING
THE ABOVE WARNINGS.
- 8 -
