background image

21

EN

20

EN

11/ PROGRAMMING

11/ PROGRAMMING

Advice:

Consult the Programmes table on the preceding pages to determine the programme you

need for the type of items, the quantity and the amount of food residue.

• 

Delaying the end of a

programme

Programme the finishing time, in quarter of an
hour stages, by pressing the + or – buttons
until you reach the desired time.

Confirm

by pressing  

“Start”

.

The screen counts down hour by hour until
the programme starts.

Cancelling a programme

Hold down the “Start / C

Ca

an

nc

ce

ell” button 

for

a few seconds.

Stopping the appliance

When the programme has finished, press the
“On/

Off

” button 

.

• 

Setting the audible signal

The setting enables you to activate or de-acti-
vate the beep at the end of the programme.

— Access the setting holding down the  

“S

ET

button

until you hear a double signal (long

beep). Keep on pressing “Set” successively until
you have access to the parameter:

The setting is confirmed automatically after
10 seconds or by pressing “SET” (switching
to the next parameter “Screen brightness”).

D

D

A

A

G

G

G

G

F

F

Waiting for delayed start

Programme time remaining,
progress

End of programme

Beep activated

Beep de-activated 

• 

Starting the appliance

Press the “O

On

n//Off” button 

to switch the

machine on.

• 

Starting a programme immediately

Select your programme by pressing one of the
selection buttons 

— The Auto programme can be accessed by pres-
sing the “AUTO” button 

.

— The 

fbutton scrolls the programmes to the

left (if the “INTENSIVE” programme is selected,
pressing this button causes the “Rapid” pro-
gramme to be selected).

— The 

button scrolls the programmes to the

right (if the “Rapid” programme is selected, pres-
sing this button causes the “INTENSIVE” pro-
gramme to be selected).

— When a programme is selected, the relevant
indicator light illuminates. The screens shows the
envisaged time that the programme will end.

Press 

“Start

/C

; the programme starts and

the screen shows the amount of time remaining
for the programme.

A short audible signal (beep) confirm the but-
ton’s selection, except for the “On/Off” button.

G

G

C

C

B

B

A

A

Programme time remaining,
progress

Finishing time

End of programme

45°C

70°C

65°C

55°C

45°C

+

-

BLANCO

F

F

Fig. 02

A

A

E

E

C

C

G

G

D

D

B

B

Summary of Contents for BFD10XP


















Reviews: