Blade 300 CFX BNF Basic, Instruction Manual

Page: 9 / 19

9
EN
AR7200BX Default Blade 300 CFX Setup
*The AR7200BX included with your Blade 300 CFX helicopter is pre-programmed with these default settings. If you perform a factory reset on the included
AR7200BX, it will default back to these helicopter settings.
To perform a Blade 300 CFX AR7200BX factory reset, enter any Setup menu and press the setup button for 10 seconds. After performing the factory reset,
you will need to re-center the swashplate servos by using setup menu G.
If you update the fi rmware on the AR7200BX to non-Blade 300 CFX fi rmware, all Blade 300 CFX helicopter default settings will be deleted. You will need
to complete the entire AR7200BX setup process before fl ying the helicopter again. Please refer to the Spektrum AR7200BX instruction manual included
with your helicopter for more information.
Status-LED: OFF Purple Red Flashing Red Solid Blue Flashing Blue Solid
A Mounting orientation
upright
(vertical) fl at (horizontal)*
B Swashplate servo— frequency User defi ned 50Hz 65Hz 120Hz 165Hz 200Hz*
C Tail servo— center position pulse length User defi ned 960μs 760μs 1520μs*
D Tail servo— frequency User defi ned 50Hz 165Hz 270Hz* 333Hz 560Hz
E Tail servo— rotor endpoints Tail stick—move to right endpoint and wait/left endpoint and wait
F Tail— sensor direction default* reversed
G Swashplate— servo centering
Reference
position ELE center pos. AIL center pos. PIT center pos.
H Swashplate— mixer User defi ned mechanical 90° 120°* 140° 140° (1=1)
I Swashplate— servo directions nor|rev|rev nor|nor|rev nor|rev|nor default*
J Swashplate— cyclic pitch geometry Aileron stick–adjust 6° cyclic pitch on the roll axis (blades aligned with fuselage)
K Collective pitch range
Collective stick on max and min position and use tail stick to adjust desired pitch
Stock settings p/- 12 degrees of collective pitch
L Swashplate— cyclic limit Move aileron, elevator and pitch sticks – adjust max limits with tail stick
M Swashplate— sensor directions rev | rev rev | nor* default nor | nor
N Pirouette optimization direction
default* reversed
Status-LED: OFF Purple Red Flashing Red Solid Blue Flashing Blue Solid
A
Swashplate—
cyclic center adjustment
Aileron and elevator stick – reset with tail stick
B Control behavior User defi ned normal sport pro extreme transmitter*
C Swashplate— pitching up behavior User defi ned very low low medium* high very high
D Tail— HeadingLock gain User defi ned very low low medium* high very high
E Stick deadband User defi ned 1 2 3* 4 5
F Tail— torque precompensation IX) User defi ned off* low—nor high—nor low—rev high—rev
G Cyclic response User defi ned normal*
slightly
increased
increased high very high
H Pitch boost User defi ned off* low medium high very high
PARAMETER MENU Menu LED is fl ashing quickly
SETUP MENU Menu LED solid
Firmware version 3103.0.0
AR7200BX Parameter Menu Tips
Refer to the Spektrum AR7200BX manual to fi ne-tune the Blade 300 CFX to
your fl ying and control style via the AR7200BX parameter menu.
If you would like to change the control behavior of the fl ybarless system to
a pre-defi ned behavior in the AR7200BX, adjust parameter menu B (default
behavior is transmitter).
If you would like to have the cyclic behavior to feel more linear OR more like
a fl ybarred helicopter, increase the cyclic response by adjusting parameter
menu G (default is ‘slightly increased’).
Refer to the Spektrum AR7200BX manual for specifi c details on each
parameter.