background image

BLADE OS 5.1 Release Notes

24

BMD00098, December 2009

Link Aggregation Control Protocol

If a static trunk on a GbESM is connected to another GbESM with LACP configured (but no active 
LACP trunk), the 

/info/l2/trunk

 command might erroneously report the static trunk as 

forwarding. 

Since LACP trunks use LACPDU packet to maintain trunking with the partner, there is a possibility 
for those packets to be dropped from an extremely busy trunk. If this happens, some links in the 
LACP trunk might be removed, then aggregated back to the trunk if an LACPDU is received. To 
avoid this unstable LACP trunk link, you can add more links to the trunk to increase the bandwidth, 
or use regular static trunk if there are no more links available.

Linking at 10/100Mb

When the link speed for an external connection is forced (i.e. no Auto-Negotiation) to 100 Mbps 
and then changed to 10 Mbps, if the external device is changed first, the external device may 
erroneously report the link as DOWN even after the GbESM is changed to 10 Mbps.

Solution: At the external device, disconnect and reconnect the cable.

Static Mrouter

If a port has a static multicast router (Mrouter) configured, and you move the port to a different 
VLAN, the static Mrouter appears in the 

/info/l3/igmp/mrouter/dump

 output for the 

original VLAN.

Solution: When you move the port to a new VLAN, remove the static Mrouter from the port, and 
add it again.

QoS Metering

Traffic may exceed the configured maximum burst size of the ACL meter 

(/cfg/port

<x>

/aclqos/meter/mbsize

) by one packet, with that packet remaining 

In-Profile. Once the ACL meter has been exceeded, additional burst packets fall Out-of-Profile. 

QoS and Trunking

When you assign an ACL (or ACL Group) to one port in a trunk, BLADEOS does not automatically 
assign the ACL to other ports in the trunk, and it does not prompt you to assign the ACL to other 
ports in the trunk. 

Solution: Manually assign each ACL or ACL Group to all ports in a trunk. 

Summary of Contents for BLADEOS 5.1



























Reviews: