BLACKMER XL2B Installation, Operation And Maintenance Instructions Download

Page: 1 / 16

BLACKMER POWER PUMPS

960260

INSTRUCTIONS NO. 107-B00

INSTALLATION OPERATION AND MAINTENANCE INSTRUCTIONS

Section

Effective

Replaces

107
Jul 2018
Jan 2014

MODELS: XL2B, XL3B, XL4C

TABLE OF CONTENTS

Page

PUMP DATA

Technical

Data

Initial Pump Start Up Information

INSTALLATION

Pre-Installation

Cleaning

Location and Piping

Mounting

Coupling

Alignment

Pump

Rotation

To Change Pump Rotation

Check

Valves

OPERATION

Pre-Start Up Check List

Start Up Procedures

Running the Pump in Reverse Rotation

Flushing the Pump

Pump Relief Valve

Relief Valve Setting and Adjustment

MAINTENANCE

Lubrication 7
Strainers 7
Vane Replacement

Pump Disassembly

Parts Replacement

Pump Assembly

FLANGE MOUNTED GEAR REDUCER MAIN.

TROUBLE SHOOTING

NOTE

: Numbers in parentheses following individual parts

indicate reference numbers on Blackmer Parts Lists.

Blackmer pump manuals and parts lists may be obtained
from Blackmer's website (www.blackmer.com) or by
contacting Blackmer Customer Service.

Pump Parts Lists

2 and 3 - inch

4 - inch

107-B01 107-B02

SAFETY DATA

This is a SAFETY ALERT SYMBOL.

When you see this symbol on the product, or in the

manual, look for one of the following signal words and be

alert to the potential for personal injury, death or major

property damage

Warns of hazards that WILL cause serious personal injury,

death or major property damage.

Warns of hazards that CAN cause serious personal injury,

death or major property damage.

Warns of hazards that CAN cause personal injury

or property damage.

NOTICE:

Indicates special instructions which are very

important and must be followed.

NOTICE:

Blackmer Pumps

MUST

only be installed in systems,

which have been designed by qualified engineering
personnel. The system

MUST

conform to all applicable

local and national regulations and safety standards.

This manual is intended to assist in the installation and
operation of the Blackmer power pumps, and

MUST

kept with the pump.

Pump service shall be performed by qualified technicians

ONLY

. Service shall conform to all applicable local and

national regulations and safety standards.

Thoroughly review this manual, all instructions and hazard
warnings,

BEFORE

performing any work on the pump.

Maintain

ALL

system and pump operation and hazard

warning decals.

Summary of Contents for XL2B

















Search results

Summary of Contents for XL2B

Reviews:

Related manuals for XL2B

Brands by name

Popular brands

BLACKMER XL2B, Installation, Operation And Maintenance Instructions

Search results

Summary of Contents for XL2B

Reviews:

Related manuals for XL2B

Brands by name

Popular brands