FRONT OR REAR
AVANT OU ARRIÈRE
VORDER- ODER RÜCKSEITE
Expandable to fit most bikes
Extensible pour ada
pta
tion sur la plupart des vélos
Erweiterbar
, passend für die meisten F
ahrräder
Expandable to fit most bikes
Extensible pour ada
pta
tion sur la plupart des vélos
Erweiterbar
, passend für die meisten F
ahrräder
OUTPOST
FAT BIKE
™
Rack / Porte-bagages
LIFETIME
WARRANTY
2x
Extenders / Extensions / Verlängerungen
300mm
2x
Cam Lock / Verrou à Came / Cam Lock
2x
Eyelet / Œil / Öse
2x
Bolts / Boulons / Schrauben
16mm M5
2x
Swivel Bolts / Boulons Orientables /
Schwenkriegel
18mm M5
2x
Swivel Bolts / Boulons Orientables /
Konkave Unterlegscheiben
25mm M6
2x
Concave Washers / Rondelles Honcaves /
Concave Washers
2x
Seat Stay Clamp—Small / Attache pour Tige
de Selle—Petite / Sitzstrebenklemme—Klein
2x
Seat Stay Clamp—Large /
Attache pour Tige de sSelle—Grande /
Sitzstrebenklemme—Groß
2x
Nylock Nut / Écrou Nylock /
Selbstsichernde Mutter
1x
Allen Key / Clé Hexagonale / Inbusschlüssel
4mm
STEP 1. ASSEMBLY:
Assemble the two struts and
top deck as shown. Either configuration may work for
front usage, however, the top deck requires at least
20mm of clearance from the fork or bike components.
Do not tighten set screws on top deck.
STEP 2. ATTACH STRUTS:
The lower mount of this
rack is designed to attach to bicycle using either M5
bolts (Option 1) or with an extra long quick release
(included, Option 2).
Option 1.
Slide rack struts to fit on the outside of
the bike frame. Attach rack to lower “braze ons” with
supplied M5 bolts. Do not fully tighten.
Option 2.
This option allows for the fitment of rack
if a lower “braze on” is not available.
Remove quick
release. Slide rack struts to fit on the outside of the
dropouts. Install extra long quick release through the
lower mount and bicycle hub. Follow your bicycle/
wheel manufacturer recommendations for removing
and installing quick release or have a qualified bicycle
shop replace it for you. Tighten top deck set screws
to lock sliding struts in place (torque = 6-8 Nm).
STEP 3. ADJUST HEIGHT:
The lower mounts
allow for optimization of the height of the rack to
accommodate different wheel diameters. There are
five height settings that allow the rack to move up or
down. To adjust the height, remove the flat head M6
bolt on each side of the lower mount. Slide the rack
up or down and reinstall the flat head bolt (torque
= 3.5–5 Nm) on lowest setting that allows at least
20mm between the tire and rack.
STEP 4. ATTACH EXTENDERS:
There are three
options available to attach the extenders depending
on the bicycle setup.
Option 1.
For bikes with seat stay or fork “braze
ons.”
Place the cam lock onto one side of the rack
strut and slide the extenders through the cam lock
holes with the straight end toward the bike. Attach
the extender to the frame or fork “braze on” using the
supplied M5 swivel bolt and concave washer. Do not
tighten. Adjust rack until top is level with ground by
sliding it on the extender. Once level, tighten cam lock
bolt. Repeat this step on the other side of the rack
strut.
Option 2.
If Option 1 is not available, then use the
cantilever brake mounts.
Remove the eyelet from
the straight end of the extender and install on the
opposite end with 90 degree bend. Place the cam
lock onto one side of the front rack strut and slide
the extender through the cam lock holes with the 90
degree bend end toward the brake mount. Remove
the bicycles cantilever brake mount bolt and attach
the extender to the frame brake mount using the
supplied M6 swivel bolt and concave washer. Do not
tighten. Adjust rack until top is level with ground by
sliding it on the extenders. Once level, tighten cam
lock bolt (torque = 6-8 Nm). Repeat this step on the
other side of the rack strut.
Option 3.
For MTN & Recreational bikes. If Option
1 and 2 are not feasible, then use vinyl coated
seat stay clamps (2 sizes included).
Attach with M5
Swivel bolts and nylock nuts.
STEP 5. TRIM EXTENDERS:
Mark each of the
extenders approximately 10mm behind the cam lock.
Remove the extenders one at a time and cut at the
mark with a hacksaw or pipe cutter. Gently file any
rough edges from cutting the extender. Reinstall the
extenders following the instructions in Step 4.
STEP 6. TIGHTEN BOLTS:
Tighten each of the bolts
attached during the previous Steps according to the
bike and/or component manufacturer’s specifications.
Go to www.blackburndesign.com for updates on this
document.
© 2014 Bell Sports, Inc.
Customer Service: 1-800-456-2355
Printed in China
blackburndesign.com
WARNING:
Periodically check all nuts and bolts for tightness.
AVERTISSEMENT :
Vérifier périodiquement le serrage de tous les écrous et boulons.
WARNUNG:
Überprüfen Sie regelmäßig alle Schrauben und Muttern auf festen Sitz.
STEP 2
—Option 1
ÉTAPE 2
—Option 1
SCHRITT 2
—Option 1
STEP 2
—Option 2
ÉTAPE 2
—Option 2
SCHRITT
—Option 2
STEP 4
—Option 1
ÉTAPE 4
—Option 1
SCHRITT 4
—Option 1
STEP 4
—Option 2
ÉTAPE 4
—Option 2
SCHRITT 4
—Option 2
STEP 4
—Option 3
ÉTAPE 4
—Option 3
SCHRITT 4
—Option 3
M5 Bolt
Boulon M5
M5-Bolzen
M5 Bolt
Boulon M5
M5-Bolzen
Nut
Écrou
Mutter
Extra Long Quick Release
Déconnexion Rapide Extra-longue
Extralanger Schnellspanner
Concave
Washer
Rondelle
Concave
Konkave
Unterlegscheibe
M5 Swivel Bolt
Boulon M5
Orientables
M5-
Schwenkriegel
M6
Swivel
Bolt
Boulon M6
Orientables
M6-
Schwenkriegel
M5 Swivel
Bolt
Boulon M5
Orientables
M5-Schwenkriegel
Vinyl Clamps
(For bikes without braze-ons)
Attaches en Vinyle
(Pour bicyclettes sans points
d’attaches brasés)
Vinylschellen
(Für Räder ohne Anlötteile)
FRONT ONLY
AVANT SEULEMENT
NUR VORDERSEITE
Concave
Washer
Rondelle
Concave
Konkave
Unterlegscheibe
