Black Widow Security BW IM 1 Installation Manual Download Page 4

4

© DLC, Inc.

65-IMM Rev. 1, 07/02

Remote Programmable Features

To change programmable feature:

1. Turn off the Auto Transmit mode.*
2. Turn on the ignition.
3. Wait 2 seconds.
4. Within 10 seconds press valet switch 5 times.

• The LED flashes 3 times indicating the system

is now in program mode.

5. Press valet switch the number of times that

equal to the feature you wish to change.
(Example: to turn feature #3 off press the valet
switch 3 times).

• The LED will flash each time the switch is

pushed.

6. Press the transmitter button to reverse the

current setting.

7. Turn off the ignition.

*

If the Auto Transmit mode is left on, the

programmable features may be reset to the
default settings or undesired operation may result.

NOTE:

You must re-enter program mode for each

feature you wish to change.

Programmable Features

Program #1: Ignition Lock

On = Ignition auto lock
Off = No ignition auto lock

Program #2: Passive Unlock

On = Passive w/unlock
Off = Passive no unlock 

Program #3: Normal/Silent Arming

On = Silent operation 
Off = Normal operation

Program #4: Door Unlock Pulse

On = Single
Off = Double

Program #5: Door Lock Pulse Length

On = 0.7 second door lock/unlock pulse
Off = 3 second door lock/unlock pulse 

Program #6: Wire # 9 Output on Disarm

On = Dome Light Output for 30 seconds
Off = Factory Alarm DisarmOutput

Program #7: Anti-Carjack Feature

On = Anti-Carjacking Enabled
Off = Anti-Carjacking Disabled 

Default Reset

To reset all programmable features to the factory
default settings:

1. Turn on the ignition.
2. Wait 2 seconds.
3. Within 10 seconds press valet switch 5 times.

• The LED flashes four times indicating the sys-

tem is now in program mode.

4. Press the transmitter button once. The LED

will flash 4 times and all programmable features
will be reset to the 

On

position.

R

emote Programmable Features:

Step

Function

On (Default)

Off

1.

Ignition Lock

On

Off

2.

Passive Unlock

On

Off

3.

Normal/Silent Arming

Silent

Normal

4.

Door Unlock Pulse

Single

Double

5.

Door Lock Pulse Length

.75 Seconds

3 Seconds

6.

Wire #9 Output on Disarm

Dome Light Output

Factory Alarm Disarm

7.

Anti-Carjack Feature

Enabled

Disabled

Summary of Contents for BW IM 1

Page 1: ...steps below to code a replacement trans mitter into the system maximum of 4 If there are less than 4 transmitters code the last transmitter multiple times to fill all 4 transmitter slots and force any lost or stolen transmitters out of the system To enter Code Learning Mode 1 Turn ignition key on off on off and leave on within 5 seconds The LED will will flash 3 times 2 Press and hold the valet sw...

Page 2: ...V low current output for relay modules or inverters 100mA relay trigger only Do NOT use as a power source for door lock relays GREENWIRE negative lock output 2 Pin Red Connector Plug in connector port for LED Mount LED in an area where it may be easily seen from either side of the vehicle 2 Pin Blue Connector Plug in connector port for Valet switch Mount the switch in an area that is easi ly acces...

Page 3: ...ot interfere and cause unwanted disarming when the vehicle is parked in very close proximity HORN CHIRPS For audible confirmation of the ARM and DISARM functions the horn can be programmed to chirp This feature requires the optional horn output to be connected and programmed during installation IGNITION LOCK The ignition locking feature allows the doors to automatically lock and unlock when the ig...

Page 4: ... no unlock Program 3 Normal Silent Arming On Silent operation Off Normal operation Program 4 Door Unlock Pulse On Single Off Double Program 5 Door Lock Pulse Length On 0 7 second door lock unlock pulse Off 3 second door lock unlock pulse Program 6 Wire 9 Output on Disarm On Dome Light Output for 30 seconds Off Factory Alarm DisarmOutput Program 7 Anti Carjack Feature On Anti Carjacking Enabled Off...

Reviews: