Fu
rn
itu
re
Us
e
and
Ma
inte
na
nce
EN
§
Fu
rnitu
re
As
se
m
bly
Explanations / Possible notes used in the Assembly
Instructions:
§1
§2
§3
1.
2.
4.
5.
6.
7.
1.
Furniture units must be placed on a level surface and levelled.
2.
Check the condition of the cam pins while the furniture is in use.
T
ighten if necessary
.
4.
Furniture must be placed in dry rooms, with working ventilation, and at least 1 m from active heat sources.
The rooms must be protected against
detrimental weather conditions (sunlight, rain, etc.).
6.
Furniture must be moved by being lifted it with no load on it. Note: shifting or dragging furniture may cause permanent damage. When moving,
hold the vertical elements of the unit, i.e. the sides and legs. Do not grab the horizontal elements, e.g. structural shelves or drawers, as these are
prone to damage.
7.
Clean furniture using a damp cloth or paper towel.
3.
NOTE!! Do not climb on furniture.
5.NOTE!! Placing excessive loads on furniture is dangerous to users and may cause permanent damage.
§5
§6
§7
§8
§9
§4
Drill holes according to drawings. During this operation take
special care not to cut yourself or damage the component!
§10
§11
§1
2
§1
3
§1
4
§1
5
§1
6
§1
8
§1
7
NOTE!!
C
om
p
o
ne
n
t
sym
b
o
l
C
o
d
e
Pack
A
B
C
D
E
D
im
e
n
si
o
n
s
[m
m
]
Quantity[pcs]
NOTE!!
NOTE!!
NOTE!!
The first stage of the assembly involves fitting the components with
t
he proper accessories as specified on the drawings below
.
The symbol
denotes places where special caution is required
during assembly
.
NOTE!!
L ack o for improper adjustment poses risk of
flap
door
falling
freely
.
Attach unit
to wall when
completely assembled. Improperly
attached furniture may break free and fall while
being
mounted
or used.The
unit
may only be attached to the wall by a
qualified
person. Check that the wall is suitable fo rhaving furniture attached to it before hand.
Choose a suitable anchor bolt
and
check the strength and quality
of the attachment.
Place the top unit
on the base unit
then join
them using
connector plate n52 and screws p25. The unit
may break free
and fall during
use if this instruction
is not followed.
Assemble the unit according to the drawings below using the
specified connectors and/or joints.
The drawer must be assembled with great caution so as not to
damage its fragile frame connections.
Apply glue y1 into the holes of the depicted component, attach it and
wait for the glue to dry
.
Clean the glued area thoroughly
.
Adjustment
T
ighten the screws e8 so they do not project over the rim.
Option
P
lace the insert upside down onto the frame in place designed for
that component using the unfolded top unit.
Install the mattress.
IMPORT
ANT!!! Due to safe ty reasons,
there must be at least 230mm between the top edge of components
A and B and the level of the mattress. When
using the space underneath the bed, pay attention"!
”
t o the
protruding edge of component C. Be warned that small children (under 6 years of age) are at risk of falling from the top bed.
Use security tape as this is essential to ensure the safety of those who use your furniture.
NOTE!!
Handle glass components with extra caution so as not to cut
yourself or damage or break the components.
Connect the adjoining units using VHS connecting screws.
§1
9
The door may be installed either on the left or the right side of the
unit.
§2
0
NOTE!!
B
ed unit and flap have a tendency to slam when
closing. There is a risk of injury
.
§2
1
Apply masking strip/unit in visible places.
§2
2
2
A
B
A=B
4
f1
3
6
1
3.
5
n26
1
p38
x
1
6
mm
§2
3
NOTE!!
High gloss fronts are covered with a protective film which
is to be removed once the component has been hung up.
The surface of these fronts cannot be cleaned until least 4 weeks
after removing the protective film.
NOTE!!
Furniture may break free and fall if not used with caution.
Note: Before starting to assemble furniture, please read all the Furniture
Assembly Instructions including the rules for maintenance and use.
Follow the sequence of individual assembly stages according to the paragraphs provided in the General Rules for Furniture
Assembly
.
KEEP
THESE INSTRUCTIONS FOR THE DURA
TION OF FURNITURE USE.
1.
NOTE!
Do not proceed with assembly if any components are defective or damaged.
2.
Place the components on a soft, clean surface, e.g. a towel or blanket, during assembly
. Do not assemble furniture on rags, carpets, etc.
3.
Drive the dowel pins f1 into the 8mm diameter holes, located on components' edges. Leave the cam bolt holes free.
Any pin that sticks out by more
than 10mm needs to be taken out, replaced and shortened as it may damage the side wall during assembly
.
4.
Make sure that the diagonals are of equal length before attaching the back wall.
5.
NOTE!
Safety strap. Install according to instructions. Improperly secured furniture may break free and fall during use.
6.
Dear Customer
, in case of complaints please quote the code number provided on the first page of the
Assembly Instructions. Report all comments
and complaints where you purchased the furniture. If possible, provide a label of defective product indicating the packing date and the packer
.
Set screw adjusts cabinet flap door opening (tighten the screw for
the
cabinet flap door to fall more freely).
