background image

B-25J MITCHELL.

              

                                       

INSTRUCTION MANUAL

3

 + This is not a toy

+  Be sure that no other flyers are using your

radio frequency.

 +The glow plug clip must be securely attached

to the glow plug.

+  Do not flip the propeller with your fingers.

+  Keep loose clothing and wires away from

the propeller.

+  Do not st art the motor if people are near .

Do not stand in line with the side of the propel-

ler.

            SAFETY PRECAUTION.

Caution:

 this model is not a toy!

If you are a beginner to this type of powered

model, please ask an experienced model flyer

for help and support. If you attempt to operate

the model without knowing what you are doing

you could easily injure yourself or somebody

else. Please keep your safety and well-being

in mind at all times.

Important:

 

before you start construction

Even if you have already built a large number

of RC models please read right through these

instructions and check all the kit components

against the parts list. We have taken great

trouble to keep construction as simple as

possible, without making any compromises

in the area of safety.

Note regarding the film covering

Minor creases or bubbles may develop in the

film covering due to major fluctuations in

weather conditions (temperature, humidity

etc.); in rare cases you may even find a slight

warp in a component. These minor faults are

in the nature of film-covered built-up wooden

structures, and can easily be corrected using

a heat gun, as commonly used for modelling.

Creases:

Blow warm air over the area

and rub down with a soft

cloth.

Wing warp:

Hold the panel twisted

gently in the opposite

direction to the warp, and

apply warm air to remove

the creases from the

covering.

Caution! do not heat the film more than is

absolutely necessary. If the air or the iron is

too hot, the film may melt and holes may be

formed.

This model is highly pre-fabricated and can

be built in a very short time. However, the work

which you have to carry out is important and

must be done carefully. The model will only

be strong and fly well if you complete your

tasks competently - so please work slowly

and accurately.

When self-tapping screws have to be
screwed into wood, apply a little white
glue to prevent them shaking loose: just
squirt white glue into the hole and fit the
screw.

 REPLACEMENT LARGE PARTS

 REPLACEMENT SMALL PARTS

A.  Wing panel.
B. Fuselage.
C. Horizontal stabilizer.

 D. Vertical stabilizer.

1. Cowling.
3.Guns & Radiator.

2.Gun turret.

4. Retractable landing gear and retractable

nose gear.

5. Wheels.

 E. Decal sheet.

6. Radiator.

7. Top fuselage hatch.

1

1

2

3

2

4

6

7

F.  Aluminium wing dihedral brace.

A

A

B

C

D

E

F

5

8.Font Greenhouse Canopy  .

8

9

9.Main Cockpit canopy .

Summary of Contents for A-BH051
















































Reviews: