background image

  

PIPER CUB- EP.                                                    

 

INSTRUCTION MANUAL

21

 

  

  

1) We highly recommend setting up a

plane using the control throws listed.

 

  

  

2) The control throws should be meas-

ured at the widest point of each control sur-
face.

 

  

  

3) Check to be sure the control surfaces

move in the correct directions.

CONTROL THROWS.

 

  

  

1) Completely charge your transmitter and

receiver batteries  before your first day of fly-
ing.

 

  

  

2) Check every bolt and every glue joint in

your plane to ensure that everything is tight
and well bonded.

 

  

  

3)  Double check the balance of the

airplane.

 

  

  

4) Check the control surface.

 

  

  

5) Check the receiver antenna . It should

be fully extended and not coiled up inside the
fuselage.

 

  

  

6) Properly balance the propeller.

PRE-FLIGHT CHECK.

      Ailerons :  10mm up         10mm down
      Elevator : 15mm up         15mm down
      Rudder :   20mm right      20mm left

Aileron Control

15

15

20
20

10

 10

We wish you many  safe and enjoyable

flights with your PIPER - CUB.

CG

65mm

Summary of Contents for NC76510






















Reviews: