To replace the blade:
u
Offer the blade up to bolt shaft and locate the blade bolt
(25) into the bolt shaft.
Note: When
a blade, the text on the blade must be
facing the user.
u
Tighten the blade bolt (25) as
as possible by hand.
u
Using heavy-duty gloves, grip the blade.
u
Use a 13 mm spanner to securely tighten the blade bolt
(25) by turning the spanner clockwise (c).
Replacement blades available
Cat No: A6314-XJ for EMax34IN,EMax34SN Type 01 only
Cat No: A6307-XJ for EMax38IN
Cat No: A6308-XJ for EMax42IN
Use
Warning! Let the appliance work at its own pace. Do not
overload.
3
ENGLISH
(Original instructions)
The height of cut is adjusted by the central height adjust
mechanism, there are 6 positions to choose from.
To set the height of cut
u
Pull the height adjustment lever (6) away from the body of
the unit.
u
Move the lever towards the rear of the appliance to lower
the height of cut.
u
Move the lever towards the front of the appliance to raise
the height of cut.
u
Push the height adjustment lever (6) into one of the 6
height locations.
Note: The height of cut can be viewed on the height of cut
gauge (7) on the side of the unit.
Switching on
u
Push in and hold the lock-off button (27).
u
Pull the on/off switch (2) towards the handle.
u
Release the lock-off button.
Switching off
u
Release the on/off switch (2).
Warning: Never attempt to lock a switch in the on position.
We recommend to use your mower as outlined in this section
in order to achieve optimum results and to reduce the risk of
cutting the mains cable.
u
Loop the mains cable through the intelligent cable
management system (4) as shown
H) ensure that
you leave approximately 100 cm of cable between the
switchbox (1) and the intelligent cable management
restraint (4).
u
Ensure that the cable restraint can slide freely from one
handle to the other.
u
Place the bulk of the mains cable on the lawn, close to the
starting point (position 1 in O1).
u
Switch the appliance on as described above.
u
Proceed as shown in
in O1
u
Move from position 1 to position 2.
u
Turn right, stepping over the cable and proceed towards
position 3. The cable restraint will slide from one side of
the handle to the other ensuring that the cable is laid out
away from the cutting blade.
u
Turn left, stepping over the cable and move towards
position 4. The cable restraint will slide from one side of
the handle to the other ensuring that the cable is laid out
away from the cutting blade.
u
Repeat the above procedure as required.
Warning: Do not work towards the cable as shown in O2.
We recommend to use your mower as outlined in this section
in order to achieve optimum results and to reduce the risk of
cutting the mains cable.
u
Place the bulk of the mains cable on the lawn, close to the
starting point (position 1 in O1).
u
Switch the appliance on as described above.
u
Proceed as shown inin O1
u
Move from position 1 to position 2.
u
Turn right and proceed towards position 3.
u
Turn left and move towards position 4.
u
Repeat the above procedure as required.
Warning: Do not work towards the cable as shown in O2.
EdgeMax allows you to cut grass right up to the edge of a wall
or fence K1).
EdgeMax allows you to accurately cut grass right up to the
edge of your lawn K2).
u
With the lawnmower parallel with the edge of your lawn.
u
Push the lawnmower along the edge of the lawn. Ensure
that the EdgeMax (9) is slightly over the edge of your lawn
K2)
Note: The roller underneath the appliance provides stability
when mowing over the edge of your lawn.
When mowing the will open, once the box is full, the
closes indicating the need to empty.
EMax34SN & EMax34IN only)
EMax38IN & EMax42IN only)
