Black+Decker BDT555KIT, Original Instructions Manual

Page: 9 / 128

9
ENGLISH (Original instructions)
u
When the wound cutting line reaches the recesses (24),
cut the line. Let the line protrude approx. 11 cm from the
spool and hold a finger on the line to keep it in place (fig.
M).
u
Proceed as described above to fit the spool on the tool.
Warning! Only use the appropriate type of BLACK+DECKER
cutting line.
Troubleshooting
If your tool seems not to operate properly, follow the instruc -
tions below. If this does not solve the problem, please contact
your local BLACK+DECKER repair agent.
Warning! Before proceeding, unplug the tool.
Appliance runs slowly
u
Check that the spool housing can rotate freely. Carefully
clean it if necessary.
u
Check that the cutting line does not protrude more than
11 cm from the spool housing. If it does, cut it off so that it
just reaches the line trimming blade.
Automatic line feed does not work
u
Keep the tabs depressed and remove the spool cover
from the housing.
u
Pull the cutting line until it protrudes 11 cm from the hous -
ing. If insufficient cutting line is left on the spool, install a
new spool of cutting line as instructed above.
u
Align the tabs on the spool cover with the cut outs in the
housing.
u
Push the cover onto the housing until it snaps securely
into place.
u
If the cutting line protrudes beyond the trimming blade, cut
it off so that it just reaches the blade.
If the automatic line feed still does not work or the
spool is jammed, try the following suggestions:
u
Carefully clean the spool cover and housing.
u
Remove the spool and check if the lever can move freely.
u
Remove the spool and unwind the cutting line, then wind it
on neatly again as described above. Replace the spool as
instructed.
Maintenance
Your BLACK+DECKER corded/cordless appliance/tool has
been designed to operate over a long period of time with a
minimum of maintenance. Continuous satisfactory opera -
tion depends upon proper tool/appliance care and regular
cleaning.
Your charger does not require any maintenance apart from
regular cleaning.
Warning! Before performing any maintenance on corded/
cordless power tools:
u
Switch off and unplug the appliance/tool.
u
Or switch off and remove the battery from the appliance/
tool if the appliance/tool has a separate battery pack.
u
Or run the battery down completely if it is integral and then
switch off.
u
Unplug the charger before cleaning it. Your charger does
not require any maintenance apart from regular cleaning.
u
Regularly clean the ventilation slots in your tool/appliance
and charger using a soft brush or dry cloth.
u
Regularly clean the motor housing using a damp cloth. Do
not use any abrasive or solvent-based cleaner.
u
Regularly clean the cutting line and spool using a soft
brush or dry cloth.
u
Regularly use a blunt scraper to remove grass and dirt
from the underneath of the guard.
Protecting the environment
Z
Separate collection. Products and batteries
marked with this symbol must not be disposed of
with normal household waste.
Products and batteries contain materials that can be
recovered or recycled reducing the demand for raw materials.
Please recycle electrical products and batteries accord -
ing to local provisions. Further information is available at
www.2helpU.com
Technical data
BDT555KIT Type 1
Input Voltage V
AC
230
Power Input W 550
No-Load Speed min
-1
7500
Weight kg 2.5
Level of sound pressure:
Sound pressure (L
pA
) 80 dB(A), uncertainty (K) 1.0 dB(A)
Sound power (L
WA
) 94.8 dB(A), uncertainty (K) 1.0 dB(A)
Vibration total values (triax vector sum) according to EN 786:
Vibration emission value (a
h
) 3.8 m/s
2
, uncertainty (K) 1.5 m/s
2
EC declaration of conformity
MACHINERY DIRECTIVE
OUTDOOR NOISE DIRECTIVE
%