6
ENGLISH
(Original instructions)
7
ENGLISH
(Original instructions)
u
Do not wash light or charger with water or allow water to
get inside light or charger. Do not submerge light in water
at any time.
@
Caution! When not in use, place the tool on
its side on a stable surface where it will not
cause a tripping or falling hazard.
Some tools
with large battery packs will stand upright on the
battery pack but may be easily knocked over.
u
Never view directly with optical instruments into the light
source.
Residual risks
Additional residual risks may arise when using the tool which
may not be included in the enclosed safety warnings. These
risks can arise from misuse, prolonged use etc.
Even with the application of the relevant safety regulations
and the implementation of safety devices, certain residual
risks can not be avoided. These include:
u
Injuries caused by touching any rotating/moving parts.
u
Injuries caused when changing any parts, blades or ac-
cessories.
u
Injuries caused by prolonged use of a tool. When using
any tool for prolonged periods ensure you take regular
breaks.
u
Impairment of hearing.
u
Health hazards caused by breathing dust developed when
using your tool (example:- working with wood, especially
oak, beech and MDF).
Vibration
The declared vibration emission values stated in the technical
data and the declaration of conformity have been measured in
accordance with a standard test method provided by EN62841
and may be used for comparing one tool with another. The
declared vibration emission value may also be used in a
preliminary assessment of exposure.
Warning! The vibration emission value during actual use of
the power tool can differ from the declared value depending
on the ways in which the tool is used. The vibration level may
increase above the level stated.
When assessing vibration exposure to determine safety
measures required by 2002/44/EC to protect persons regularly
using power tools in employment, an estimation of vibration
exposure should consider, the actual conditions of use and the
way the tool is used, including taking account of all parts of the
operating cycle such as the times when the tool is switched off
and when it is running idle in addition to the trigger time.
Labels on tool
The following symbols, along with the date code, are shown
on the tool:
:
Warning!
To reduce the risk of injury, the user
must read the instruction manual.
Additional safety instructions for batteries and
chargers
Batteries
u
Never attempt to open for any reason.
u
Do not expose the battery to water.
u
Do not store in locations where the temperature may
exceed 40 °C.
u
Charge only at ambient temperatures between 10 °C and
40 °C.
u
Charge only using the charger provided with the tool.
u
When disposing of batteries, follow the instructions given
in the section "Protecting the environment".
p
Do not attempt to charge damaged batteries.
Chargers
u
Use your BLACK+DECKER charger only to charge the
battery in the tool with which it was supplied. Other batter-
ies could burst, causing personal injury and damage.
u
Never attempt to charge non-rechargeable batteries.
u
Have defective cords replaced immediately.
u
Do not expose the charger to water.
u
Do not open the charger.
u
Do not probe the charger.
$
The charger is intended for indoor use only.
+
Read the instruction manual before use.
Electrical safety
#
Your charger is double insulated; therefore no
earth wire is required. Always check that the
mains voltage corresponds to the voltage on the
rating plate. Never attempt to replace the charger
unit with a regular mains plug.
u
If the supply cord is damaged, it must be replaced by the
manufacturer or an authorised BLACK+DECKER Service
Centre in order to avoid a hazard.
Features
This tool includes some or all of the following features.
1. On/off trigger switch
2. Forward/reverse slider
3. Bit holder
4. Handle adjustment button
5. Handle
6. Charger connector
7. Flashlight
8. Flashlight button
Charging tool (fig.A)
The battery needs to be charged before first use and whenev-
er it fails to produce sufficient power on jobs that were easily
done before. The battery may become warm while charging;
this is normal and does not indicate a problem.
Warning!
Only use the charger provided to charge the tool.
u
To charge the battery, insert the charger plug (6a) into the
connector (6).
u
Plug in the charger.
u
Leave the tool connected to the charger for 10 hours.
The charger may hum and become warm while charging; this
is normal and does not indicate a problem.
Warning!
Do not charge the battery at ambient temperatures
below 10 °C or above 40 °C. Recommended charging tem-
perature: approx. 24 °C.
Fitting and removing a screwdriver bit or socket
(fig. B)
Warning!
Make certain the tool is locked to prevent switch
actuation before installing or removing accessories.
u
To fit a screwdriver bit (9), push it into the bit holder (3)
until it locates.
u
To remove a screwdriver bit, pull it straight from the bit
holder.
Use
Warning!
Let the tool work at its own pace. Do not overload.
Using the flashlight (fig. C)
u
Press the flashlight button (8) to operate the flashlight (7).
u
Press flashlight button (8) again to turn off the flashlight
(7).
Switching on and off (fig. D)
u
To operate the tool, press and hold the trigger switch (1).
u
To switch the tool off, release the trigger switch (1).
Selecting the direction of rotation (fig. E)
For tightening screws and drilling pilot holes, use forward
(clockwise) rotation. For loosening screws or removing a
jammed drill bit, use reverse (counterclockwise) rotation.
u
To select forward rotation, push the forward/reverse slider
(2) to the right.
u
To select reverse rotation, push the forward/reverse slider
(2) to the left.
u
To lock the tool, set the forward/reverse slider (2) into the
centre position.
Adjusting the handle (fig. F)
For optimum versatility, the handle (5) can be set to three
different positions.
u
Press the handle adjustment button (4).
u
Move the handle (5) into the desired position.
u
Release the handle adjustment button (4).
Maintenance
Your BLACK+DECKER tool has been designed to operate
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool
care and regular cleaning.
Your charger does not require any maintenance apart from
regular cleaning.
Warning!
Before performing any maintenance on the tool,
remove the battery from the tool. Unplug the charger before
cleaning it.
u
Regularly clean the ventilation slots in your tool and
charger using a soft brush or dry cloth.
u
Regularly clean the motor housing using a damp cloth. Do
not use any abrasive or solvent-based cleaner.
u
Regularly tap bit holder to remove any dust from the
interior.
Protecting the environment
Z
Separate collection. Products and batteries
marked with this symbol must not be disposed of
with normal household waste.
Products and batteries contain materials that can be recov-
ered or recycled reducing the demand for raw materials.
Please recycle electrical products and batteries according to
local provisions. Further information is available at
www.2helpU.com
Technical data
BDCSFL20 H1
Voltage
V
DC
3.6
No-load speed
Min
-1
180
Max. torque
(PTI Rating)
Nm
5.5
Battery Type
Li-Ion
Battery capacity
Ah
1.5
Weight
kg
0.35