4
Ordering Information
ITEM
CODE
Analog Phone Line Simulators
ALS-210, 2-Line.........................................................TS210A
ALS-215, 4-Line.........................................................TS215A
ISDN Line Simulator....................................................TS225A
Advanced Line Emulator............................................TS224A
TS210A:
Call Progress Signals/Test Tones:
Dial tone: 350 + 440 Hz
continuous;
Ringback: 440 + 480 Hz follows
ringing cadence;
Busy: 480 + 620 Hz 500 ms
on/500 ms off;
Reorder: 480 + 620 Hz 250 ms
on/250 ms off
Forced Disconnect:
COD signal
issued after 2 seconds of valid
on-hook condition; Signal
duration: 850 ms ±25 ms
Line Attenuation:
6 dB
Line Impedance:
900 ohms
Signaling:
Ring Frequency: 20 Hz;
Dial Tone Delay: 0.1 seconds;
Network Response Delay:
0.2 seconds
Connectors:
(2) RJ-11
MTBF:
40.9 years
Temperature Tolerance:
Operating:
32 to 122°F (0 to 50°C);
Storage: -4 to +140°F
(-20 to +60°C)
Humidity Tolerance:
Up to 95%,
noncondensing
Power:
Input: 120 VAC, 60 Hz, 0.18 A;
Output: 24 VDC, 0.4 A
Size:
1.5"H x 5.5"W x 9"D
(3.8 x 14 x 22.9 cm)
Weight:
1.3 lb. (0.6 kg)
TS215A:
Audio Input/Output Jack:
Audio in impedance: 10 kohms;
Audio In: -10.5 dB (-10 dBm out
with 1 V in);
Audio out impedance: 600 ohms;
Audio out: 0 dB
DTMF and Rotary Dialing
Detection:
DTMF detect rate:
40 ms (minimum);
Rotary detect rate: 8 to 22 pps
Programmable Ringing Cadence:
Rings per cycle: Up to 3 rings in
100-ms increments
Ring Source:
Sine wave:
78 VAC ±10% AC @ 20 Hz;
Square wave: 72 ±10 VRMS @
1 REN, 20 Hz;
Ring frequency: Selectable 20,
25, 30, 60 ±5% Hz;
Drive capacity: Up to 5 ringer
equivalents (5 REN) total @
20 Hz sine wave;
Ring waveform: Selectable step
approximated sine or square
wave
Telephone Line Circuit (Loop Start):
On-hook voltage: -48 ±5 VDC;
Minimum loop current: 18 mA @
500 ohms;
Nominal impedance: 900 ohms;
Insertion loss: Switchable
between -3.4 dB and -16 dB
±2 dB @ 1 kHz;
Flash hook detect: 280 to 1120 ms
Connectors:
(4) RJ-11
MTBF:
23.6 years
Temperature Tolerance:
Operating:
32 to 113°F (0 to 45°C);
Storage: -20 to +131°F
(-29 to +55°C)
Humidity Tolerance:
Up to 85%
noncondensing
Power:
Input: 115 VAC; 49–61 Hz;
Dissipation: 20 watts maximum
Size:
2.3"H x 8.5"W x 10"D
(5.8 x 21.6 x 25.4 cm)
Weight:
4.3 lb. (2 kg)
TS225A:
Cable Drop (Maximum):
Using 24-gauge copper wire:
U interface: (2) 1600 m (5249.3 ft.);
S/T interface: 100 m (328.1 ft.)
Switch Types Supported:
N1-1,
AT&T
®
Custom, DMS Custom,
ETSI
Connectors:
(4) RJ-45, 8-pin modular
Temperature Tolerance:
Operating: 32 to 122°F (0 to 50°C);
Storage: -20 to +131°F
(-29 to +55°C)
Humidity Tolerance:
Up to 85%
noncondensing
MTBF:
38.1 years
Power:
Input: 115/230 VAC, 49–61 Hz
(switch-selectable), fused at
500 milliamps for 115 VAC,
fused at 300 milliamps for
230 VAC;
Output to powered external
devices: 40 ±5 VDC, 6 watts
maximum
Size:
2.5"H x 10.5"W x 10"D
(6.4 x 26.7 x 25.4 cm)
Weight:
4.5 lb. (2 kg)
TS224A:
Call Progress Tones:
Busy Tone:
480 Hz and 620 Hz ±5%
@ -24 ±3 dBm per tone (default)
Dial Tone:
350 Hz and 440 Hz ±5% @
-13 ±3 dBm per tone (default)
Tone Levels:
200 to 3000 Hz, 1-Hz
resolution
Dialing Characteristics:
Frequency Accept:
±1.5% ±2 Hz
Rotary Detection:
8–22 pps
Telephone Interface:
Approvals:
FCC Part 15, CE
Attenuation:
4–60 dB in 1-dB steps
Impedance:
600 W ±2.2 mF or
900+2.2 mF
Loop Current:
10 to 70 mA in 1-mA
increments
Ring Cadence:
Up to 3 cycles set in
5-ms increments
Ring Frequency:
17–70 Hz in 1-Hz
increments
Ringing Source:
20–80 VAC in 5-V
increments
Power:
100–240 VAC, 50–60 Hz
Size:
2.9"H x 10"W x 13"D
(7.4 x 25.4 x 33 cm)
Weight:
7 lb. (3.2 kg)
Specifications
