Black & Decker CUA625BH, Original Instructions Manual

Page: 11 / 24

11
(Original instructions) ENGLISH
7. Charging base
7a. Accessory holder
8. Dust bowl lid hinge
9. Hose connector
10. Flexible hose
11. Handle / wand release button
12. Chassis
12a. Light
13. Chassis hose port
14. Floor
head
15. 3-in-1 Accesssory tool
16. Pet crevice tool (CUA625BHP only)
17. Long brush tool (CUA625BHA only)
22a. Scent disc (CUA625BHP only)
Use
Switching on and off (Fig. A)

To switch on, press the on/off switch (1).

Unit starts in mid performance setting. Performance can
be adjusted using power control slider (J2) Left = min
Right = max (as seen when in use from above).

To switch off, press the on/off switch (1).
Note: Use the unit in high speed mode with beater bar
switched on for carpet. Use the unit in low speed mode with
beater bar switched off for hard wood and laminate flooring.
Note: The unit has an intuitve ‘standby’ mode that allows it
to remember the last settings applied for a few minutes upon
starting up.
Note: If leaving the appliance when in use, position the upright
unit, in such a way that any inadvertent fall would contact
a wall or corner and otherwise be away from people and pets.
Control panel (Fig. J)
The unit is equipped with a smart tech control panel providing
Intelligent sensor technology for a more intuitive cleaning
experience.
The features incorporated are:
J1 FLOOR SENSOR Touch Button
Intelligent fl oor sensor technology increases suction on carpets and
switches to Economy Mode for lighter tasks, such as hard fl oor cleaning,
thus optimising the battery run time this feature is active when the LED
(J1a) is lit. In order to maximise runtime on all surfaces, switch this
feature off by touching area (J1).
J2 Power contol Touch Slider
Touch button panel allows you to control the level of power to the unit
from minimum to maximum by sliding fi nger along this area.
J3 Beater bar Touch Button
Allows you to turn the beater bar function on and off.
J4 Power indicator
Allows you to monitor the level of power being used.
J5 BATTERY SENSOR Indicator
The LED battery indicator displays the remaining charge and warns you
when the battery is low. The fi nal LED will fl ash continuously when there
is only 1 minute of runtime remaining. All LEDs will fl ash when the unit is
discharged.
J6 FILTER SENSOR
Smart sensor technology automatically detects (the symbol will light red)
when the fi lter becomes clogged and needs to be cleaned.
Note: The FILTER SENSOR LED will flash and the unit will
automatically shut down when there is any obstruction in the
flexible hose or filters which is causing the motor to overheat.
Disconnect and remove the blockage immediately.
Using the handle / wand (Fig. B, C, D, E)

Press the handle / wand release button (11) to free the
handle / wand (3) from the chassis (12).

Free the hose connector (9) from the chassis hose port
(13) as shown in
fi gure B.

Press the chassis release button (12b) to release the hand
held vac (5) from the chassis (12) as shown in
fi gure C.

Connect the hose connector (9) to the fl exible tube port
(3a) ensuring that the latch (9a) clicks securely into place
as shown in
fi gure D.

Extend the crevice tool (4) as shown in fi gure E, until it
clicks in place.

To retract the crevice tool (4) press the tube extension
latch (3b) allowing it to return to its normal position.
Using the 3-in-1 accessory tool (Fig. F)

The 3-in-1 handle / wand (15) has three con fi gurations.
1. Brush mode.
2. Small crevice mode.
3.
Upholstery mode.

The 3-in-1 handle / wand can be fi tted either directly to the
hose connector 9 or to the extendable crevice tool (4) as
shown in
fi gure F.