Recommended accessories for use with your tool are available at extra cost from your distributor or
local service center. A complete listing of service centers is included with your tool.
C
CA
AU
UT
TIIO
ON
N:: The use of any non-recommended accessory may be hazardous.
If you need any assistance in locating any accessory call 1-800-9-BD TOOL (1-800-923-8665) or con-
tact Black & Decker (U.S.) Inc., Consumer Service Department, 626 Hanover Pike, P.O. Box 618,
Hampstead, MD 21074.
E
Exxtteen
nssiio
on
n,, W
Wo
orrkk S
Su
up
pp
po
orrtt:: 3
36
68
80
00
0
Used to support long overhanging work pieces, the work support is user assembled and stores con-
veniently under the saw table. Your saw table is designed to accept two work supports; one on each
side.
A
Ad
djju
ussttaab
bllee L
Leen
ng
gtth
h S
Stto
op
p:: 3
36
68
80
01
1
Requires the use of one work support (see Figure). It is used to make repetitive cuts of the same
length from 0 to 42".
C
Cllaam
mp
p:: 3
36
68
80
02
2
Used for firmly clamping work piece to the saw fence for precision cutting
D
Du
usstt B
Baag
g:: 3
36
68
80
03
3
Equipped with a zipper for easy emptying, the dust bag will capture the majority of the sawdust pro-
duced.
N
No
ottee:: Deflector on dust spout channels debris to ground. Spout has a provision to attach a vacuum
hose to collect sawdust. Lift deflector to connect hose.
C
Crro
ow
wn
n M
Mo
olld
diin
ng
g FFeen
nccee:: 3
36
68
80
07
7
Used for precision cutting of crown molding. Position crown molding consistently at the proper
angle from cut to cut.
K
Kiitt B
Bo
oxx:: 3
36
68
80
06
6
Used to store and transport accessories.
12
A
AP
PP
PL
LIIC
CA
AT
TIIO
ON
N
B
BL
LA
AD
DE
E
N
NO
O.. O
OFF T
TE
EE
ET
TH
H
T
TY
YP
PE
E O
OFF C
CU
UT
T
Fine Trim Molding
Precision
60-100
Very smooth
Ground Carbide
splinter free
Trim, Framing, Pressure-
Combination
32-60
Smooth fast cut
Treated Decking
Multi-Purpose
Aluminum
Non-Ferrous
60-80
____
Metal Cutting
ACCESSORIES
MAINTENANCE
1. All bearings are sealed ball bearings. They are lubricated for life and need no further maintenance.
2. Periodically clean all dust and wood chips from around AND UNDER the base and the rotary
table. Even though slots are provided to allow debris to pass through, some dust will accumulate.
3. The brushes are designed to give you several years of use. If they ever need replacement follow
the instructions below or return the tool to the nearest service center for repair. Service center
locations are packed with your tool.
Brushes
Inspect carbon brushes regularly:
1. TURN OFF TOOL AND DISCONNECT FROM POWER SUPPLY.
2. Remove the brush inspection cap.
3. Withdraw the brush assembly.
4. Keep brushes clean and sliding freely in their guides. Always replace a used brush in the same ori-
entation in the holder as it was prior to its removal. Carbon brushes have varying symbols stamped
into their sides, and if the brush is worn down to the line closest to the spring, they must be
replaced. (If either brush is worn out, replace both.) Use only identical B&D brushes. Use of the
correct grade of brush is essential for proper operation of electric brake. New brush assemblies are
available at B&D service centers.
5. The tool should be allowed to “run in” (run at no load) for 10 minutes before use to seat new
brushes. The electric brake may be erratic in operation until the brushes are properly seated (worn
in).
N
NO
OT
TE
E:: While “running in” DO NOT TIE, TAPE, OR OTHERWISE LOCK THE TRIGGER SWITCH ON.
HOLD BY HAND ONLY.
