manualshive.com logo in svg

BK Radio GPH Flex Mode, User Manual

Share
Download
BK Radio GPH Flex Mode User Manual Download Page 23

24

 

 

BK Radio

 

BUSY CHANNEL LOCKOUT 

The busy channel lockout feature applies only to 
those channels programmed to receive Code 
Guard operation. When carrier activity is detected 
on the channel selected, the radio checks the 
receive Code Guard value. If the proper Code 
Guard value is present, the radio can transmit on 
that channel, even if the squelch knob is not in the 
Code Guard position.  

If the radio detects an incorrect value or carrier 
activity only, the transmitter is disabled, an alert 
tone is heard, and the display shows the word 
“

B

USY

” when the PTT switch is pressed, whether 

the squelch knob is in or out of the Code Guard 
detent.  

Channels not programmed to receive Code 
Guard operation can be used to transmit 
regardless of carrier activity.  

 
 
 
 
 
 
 

  

BUSY CHANNEL LOCKOUT OVERRIDE 

This mode operates in the same manner as busy 
channel lockout except that the user can override 
and transmit by turning the squelch knob off the 
Code Guard detent. The transmitter is locked out 
only if the squelch knob is set to the Code Guard 
detent. 

 

B U S Y 

Summary of Contents for GPH Flex Mode






























Reviews:

No comments

Brands by name

Popular brands

Load more brands