manualshive.com logo in svg

BJS Biotechnologies XXPRESS NGx, User Manual, Page: 52 / 57

Share
Download
BJS Biotechnologies XXPRESS NGx User Manual Download Page 52

P a g e

 | 

52 

 

XXPRESS® NGX USER MANUAL 

– XP-5001-01-5   

 

 

8.3  Decontamination Procedure 

The unit and accessories should be decontaminated using the following 
procedure before being stored or transported. 
 

Decontamination Procedure 

Thoroughly clean all outside surfaces of the product (including any 
accessories,  power  cords,  manuals,  packaging,  etc)  with  a  damp 
cloth soaked with suitable disinfectant solution (such as Virkon).  

 
 

8.4  Transportation and Storage 

The 

xxpress

®

NGx 

unit  and  its  accessories  should  be  thoroughly 

decontaminated using the procedure detailed in Section 8.3 before being 
placed in its original packaging for transportation or storage. 
 

 

 

WARNING

 

Refer to Section 4 for the acceptable range of Storage and 
Transportation environmental conditions. 

Always ensure that the unit and accessories are completely 
dry and free of any condensation before being packed. 

  

 

Summary of Contents for XXPRESS NGx


























































Reviews:

No comments