manualshive.com logo in svg

Bitzer SE-i1, Technical Information, Page: 26 / 56

Share
Download
Bitzer SE-i1 Technical Information Download Page 26

CT-110-2

26

7

Data communication with the SE-i1

7.1

BEST SOFTWARE

The BEST SOFTWARE displays all active alarms and
the following operating parameters:

• Compressor frequency

• Evaporation temperature

• Condensing temperature

• Low pressure

• High pressure

• Discharge gas temperature / oil temperature

7.1.1

Establishing communication via the
BEST SOFTWARE

Requirements

• PC/mobile device

– equipped with the operating system Windows 7 or

newer

– with USB port

– with BEST SOFTWARE installed

The BEST SOFTWARE can be downloaded for
free from the BITZER website (www.bitzer.de).

• Data connection via BEST interface converter

Setting up communication (see figure 25, page 26)

• Plug the BEST interface converter into the SE-i1

(COM3) and the mobile device.

• Switch on the PC/mobile device and start the

BEST SOFTWARE.

• Click the N

EW

 button (2).

A window displaying the available devices opens.

• Select SE-i1 (3).

• Click the C

ONNECT

 button (4).

The SE-i1 is now connected to the PC/mobile device.

Fig. 25: Connecting SE-i1 to the BEST SOFTWARE

Configure SE-i1, see chapter Configuring the comple-
tion sensor kit with the BEST SOFTWARE, page 12.

7.1.2

BEST SOFTWARE data log

All monitored operating parameters and alarm mes-
sages are stored internally:

• All operating parameters in 10-second-intervals,

storage period approx. 4 weeks in case of normal
operating behaviour.

• Alarm messages of the last 365 days

• Statistics for the last 365 days

These data can be directly visualized or exported as
files by using the BEST SOFTWARE. They enable an
analysis of the system operation and detailed error dia-
gnostics if necessary.

7.2

Interface for communication via Modbus RTU

For communication with superior system controllers or
the building control system, the following interfaces are
additionally available:

• Modbus RTU via RS485, terminals "Con-

trol" (COM1).

For the explanation and set-up of these interfaces, in-
cluding the register or address definition, see Refer-
ence Guide CG-110.

Summary of Contents for SE-i1

























































Reviews:

No comments