Bittium NeurOne User Manual Download Page 49

Page: 49 / 191

Page 49 of 191

800581-2.11 NeurOne System User Manual.doc

4.14.4 Battery Pack 7.2 V for Tesla amplifier

The side panel of the Battery Pack 12 V contains the following components.

Green/Orange Indicator Led

– Green light indicates high output voltage

and orange light indicates low output voltage (below 5.5 V).

Power Switch

Power Out / Charger

– Tesla amplifier or to Battery Charger for Battery Pack

7.2 V.

The battery type of Battery Pack 7.2 V is NiMH.

4.14.5 Charging the Battery Pack

4.14.5.1

Battery Pack 12V of EXG amplifier

First, make sure that the power of the Battery Pack is switched off. Connect the Battery
Charger to the Battery Pack and the Battery Charger to mains power. The

indicator

led

(1)

on the Battery Charger is red during charging. When the Battery Pack reaches

Summary of Contents for NeurOne
































































































































































































Search results

Summary of Contents for NeurOne

Reviews:

Related manuals for NeurOne

Brands by name

Popular brands

Bittium NeurOne, User Manual

Search results

Summary of Contents for NeurOne

Reviews:

Related manuals for NeurOne

Brands by name

Popular brands