Bitronics M350 User Manual Download Page 5

Page: 5 / 82

ML0038 September 27, 2017

- 5 -

50 SERIES MANUAL SET

ML0035

M650 Family User Manual

ML0036

50 Series DNP3 Protocol

ML0037

50 Series Modbus Protocol

ML0038

M350 Family User Manual

ML0039

M651 Family User Manual

ML0040

M653 Family User Manual

VERSION HISTORY (ABRIDGED)

V1.010 2010-03-25

M650M3x51x models with firmware download capability

V1.030 2010-05-14

Add

0-1mA, add per-phase power demands to protocols

V1.040 2010-06-17

Add

M350 models, add configurable display screens

V1.050 2010-07-14

Add

secondary volts screens, more info to front panel menu

V1.060

2010-07-20 Add support for B3 models

V1.070

2010-08-03 Add support for 1A input and 4-20mA output

V1.090 2010-10-27

Add

support for M651 models

V2.010

2011-02-18 Add support for configurable points/registers

V3.000

2011-09-08 Add support for M653 models, split-core CTs, passwords,

DNP3 events/Class 1, 2, 3 Reads, Primary Units

V3.020

2011-09-28 Production support changes

V3.030

2011-12-13 Modbus and DNP serial address settings configurable in

front panel menu; error reporting on front panel display

V3.060

2012-06-19 Changed password default to none

V3.070

2012-08-28 Bug fix

V3.080

2013-06-14 Add support for loss compensation calculation

V3.090

2014-04-24 Bug fix and support for the change to alphanumeric display

on the M350

V3.10

2015-08-31 Bug fix for matching baud rate of display

V3.11

2016-01-06 Lowered demand interval minimums

V3.12

2016-06-17 Front panel lock only locks menu, allows energy resets

V3.13

2016-12-07 Build no. displayed on index page; max CT ratio increased to

30,000:1

V3.15

2017-09-06 Added bus averages: Average L-L Volts, Average L-N Volts

and Average Amps (M65xM3).

Summary of Contents for M350




















































Search results

Summary of Contents for M350

Reviews:

Related manuals for M350

Brands by name

Popular brands

Bitronics M350, User Manual

Search results

Summary of Contents for M350

Reviews:

Related manuals for M350

Brands by name

Popular brands