background image

7

SmartMix Continued

Replace SmartMix concentrate bottle.

Note: If bottle leaks, check for proper 

positioning of o-ring and straw.

Choose the SmartMix setting that fits the cleaning job.

Water Rinse / Carpet Protector

- use for gentle

cleaning or for the final rinse after cleaning. This
setting must also be used when applying the carpet
protectant through the applicator, to prevent the
pump from temporarily losing its prime.

Normal

- automatically provides the best mix of

water and concentrate for most cleaning jobs.

High Traffic

- automatically mixes the right amount

of water and concentrate to dissolve tough grime
and heavy soil. Note: Residual cleaning materials left
in carpet from other products may cause excessive
foaming when picked up. If foam is overflowing
tank, move SmartMix dial to “Water Rinse/Carpet
Protector” position until the condition stops.

Note: Both the SmartMix Bottle and the clean

water tank must have liquid in them in
order for the machine to spray. If one tank
is empty, the machine will temporarily
lose its prime and not apply either 
cleaning solution or water only.

Important: If you are using the WATER RINSE /

CARPET PROTECTOR setting, fill the Smart
Mix bottle with water also!

The powered brush roll at the floor nozzle is designed to
enhance cleaning performance. The bristle pattern lifts out the
deep down dirt while gently grooming carpet fibres. The floating
suspension self-adjusts to all carpet heights and protects 
your carpet if you leave the power switch ON. When the
machine handle is in the fully upright position, Carpet Saver
automatically raises the brush off the carpet.

Our Tank-in-Tank system is designed with a bladder inside for
clean water. As you clean, the bladder will empty. Dirty water
collects in the tank outside the bladder.

Step on handle release to lay the machine handle 
down out of the way.

4.

5.

O-ring
Position

Tip:

Deep Cleaning

stairs and high
traffic areas on a
regular basis and
using the carpet
protectant can
prolong carpet
life.

DirtLifter

®

PowerBrush

WARNING: 

To reduce the risk of fire,
use only BISSELL Deep
Cleaning Formula for full
size machines in your Pro-
Heat Pro-Tech. Use of
cleaning formulas which
contain lemon or pine oil
may damage this appli-
ance and void 
warranty. Chemical spot
cleaners or solvent based
soil removers should not
be used. These products
may react with the plastic
materials used in your
ProHeat Pro-Tech, causing
cracking or pitting.

SmartMix 
Dial

1.

Tank-in-Tank

HIGH 

TRAFF

IC

WA

TER RINSE

/

CAR

PET

PROTECTOR 

NO

RMAL 

Summary of Contents for ProHeat Pro-Tech 7901 SERIES

























Reviews: