Bissell FMU-2000, Safety, Operation And Maintenance Manual With Parts List

Page: 6 / 8

(6) BISSELL BigGreen Commercial FMU-2000 Burnisher BISSELL BigGreen Commercial FMU-2000 Burnisher (11)
6.0 Handle Parts List
Drawing No. Description Part No. Qty.
1 Switch Box Back Cover A-104 1
2 Handle Tube Screw B-23 2
3 Switch Box Closing Screws B-21 4
4 Strain Relief Clip M-213 1
5 Switch Plate Screw B-68 2
6 Black Hand Grip with Green Band M-218-G 2
8 Handle Tube Insert M-247 1
9 Handle Tube Assembly M-206 1
10 Cable Hook Screw B-2 2
11 Cable Hook A-164 1
12 Sliding Collar A-111 1
13 Flat Washer B-37 1
14 Split Washer B-39 1
15 Cam Lock Wing Nut B-25 1
16 Straight Brace M-233 2
17 Stop Nut B-10 2
18 Washer B-28 2
19 Cap Screw B-9 2
20 Yoke Tube Mount Bolt B-18A 2
21 Tube Mounting Nut B-19 2
22 Yoke A-1001 1
24 Yoke Bolt B-14 1
25 Handle Tube Cable G-16 1
26 Black Rubber Cable Connector M-249 1
27 Cable Grommet B-63 1
28 Rectangular Hole Cam Washer B-67 1
29A Cam Assembly C-100 1
29B Complete Cam Assembly Kit CCA 1
(Includes 1 each of Drawing Items
#13, 14, 15, 28, 29)
30 50-Foot, 14/3-Gauge - Yellow G-14-50-Y 1
31 Insulated Flag Wire Connector G-48 2
32 On/Off Switch and Plate Assembly G-30-AB 1
33 Switch Mounting Plate G-30-B 1
34 Ground Wire Screw B-1 2
35 Int. Tooth Lock Washer B-35 1
36 Flat Hex Nut B-33 1
37 Trigger Return Spring G-30-C-T057 1
38 Label - Switchbox 1
39 Switchbox Front A-103 1
40 Wire Nut G-47 1
41 Triggers A-105 2
42 16” Crossbar M-211-A 1
43 Trigger Pins B-70 2
44 Cross Bar Screw B-22 2
45 Safety Interlock Assembly SIA-1R 1
1. Mount the handle to the chassis:
Align the handle with the yoke (1) over the mount
(2) on the burnisher chassis. The power cord will be
facing away fro the motor. Place a flat washer (4) on
a 3” bolt (3), then place the bolt through the holes
in the yoke and the mount. Place another washer on
the bolt and secure with the locking nut (5). Tip the
handle back and out of your way for the next step.
2. Mount he support braces on the handle:
Tip the handle up. The handle mounting collar (7)
is designed to slide freely up and down the handle
tube, allowing the handle to be adjusted for the
comfortable operation of all users. Line up the
mounting collar with the upper holes in the two
straight handle braces (6).
• Place the curved spacer (12) with a square hole
onto the locking lever shaft (11). The curve
must face the lever.
• From behind the machine, insert the shaft
through the right handle brace (6), the
mounting collar (7) and the left handle brace.
• Place a spacer (9) on the shaft.
• Place the split washer (13) on the shaft.
• Place the locking wing nut (14) on the shaft.
• Adjust the wing nut for tightness. When
correctly installed, the collar slides easily
when the cam-engineered locking lever is
“up,” but is firmly fixed wen the lever is
“down.”
2.0 Mount the Handle
This burnisher is shipped from the factory with the handle unattached. You will need two
7/16” wrenches to complete the assembly.
Remove the handle and mounting hardware from its carton. Bolts, nuts, washers and the
locking lever assembly are in the plastic bag attached to the handle.