BIRD Termaline 8890-300SC13 Operation Manual Download Page 8 | Manualshive

Page: 8 / 25

BIRD Termaline 8890-300SC13 Operation Manual Download Page 8

Termaline® Semiconductor Load Resistor

vii

About This Manual

This manual covers the operating and maintenance instructions for the following models:

Changes to this Manual

We have made every effort to ensure this manual is accurate. If you discover any errors, or if you have suggestions
for improving this manual, please send your comments to our Solon, Ohio factory. This manual may be periodically
updated. When inquiring about updates to this manual refer to the part number and revision on the title page.

Chapter Layout

Introduction —

Describes the features of the 8890 Semiconductor, lists equipment supplied and optional

equipment, and provides power-up instructions.

Theory of Operation —

Describes how the 8890 Semiconductor works and its functions.

Installation —

Describes the how to install the 8890 Semiconductor.

Operating Instructions —

Describes procedures require for operating the 8890 Semiconductor.

Maintenance —

Lists routine maintenance tasks as well as troubleshooting for common problems. Specifications

and parts information are also included.

8890-300SC13

«
...
6
7
8
9
10
...
»

Summary of Contents for Termaline 8890-300SC13


























Reviews:

No comments