BIRD SiteHawk SK-200-TC Operation Manual Download Page 24 | Manualshive

Page: 24 / 65

background image

Bird SiteHawk Operation Manual

15

Adjusting the trace within the selected scale

Note:

Scale settings only affect the active trace, if more than one

trace is currently displayed, select the desired trace before chang-
ing scale.

1.

Press SCALE icon. See

2.

Select one of the following from the menu:

a.

For Manual Operation:
Press Top to change upper limit of the display
Press Bottom to change the lower limit of the display

b.

For Auto Scale:
Press Auto Scale for the system to choose the best fit for the active
trace.

Note:

The scale can also be dynamically changed by pressing and

dragging the trace up or down in the display window.

Figure

6

Adjusting the Trace

«
...
22
23
24
25
26
...
»

Summary of Contents for SiteHawk SK-200-TC


































































Reviews:

No comments

Related manuals for SiteHawk SK-200-TC

Brand: Kawai Pages: 2

Brand: Datron Pages: 197

Brand: Omer Pages: 2

Brand: Daewoo Pages: 2

Brand: VEE GEE Pages: 2

Brand: Roland Pages: 15

Brand: janitza Pages: 12

Brand: AEMC Pages: 4

Brand: Keithley Pages: 18

Brand: Jenoptik Pages: 54

microCLIMA ULTRA

Brand: MADDALENA Pages: 17

Brand: JBM Pages: 4

Brand: HTC Pages: 2

Brand: Komshine Pages: 2

Brand: Bender Pages: 4

Brand: TEKELEK Pages: 3

Brand: Hall Research Technologies Pages: 24

Everywhereyoulook Frontline X500

Brand: Teledyne Lecroy Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands