4) Set the harassment switches, mode setting
switches, time-off switches, time of operation
switches and random operation switches to
the desired settings. (See “PROGRAMMING
YOUR CRITTER BLASTER PRO” for complete
details on how to program your unit).
5) Make sure the volume setting is set to LOW
(all the way counter-clockwise).
6) Slide the power switch to the ON position.
The unit may take a few seconds before
starting.
7) Adjust the volume to the desired level.
8) Close the cover and latch shut.
PROGRAMMING YOUR CRITTER BLASTER PRO
To program your Critter Blaster Pro unit you will
need a small screwdriver, toothpick, or other small,
rigid object to toggle the switches in the switch
array. The switch array is the
switch bank located in the top left
corner of the unit (under “PRO-
GRAM”) . A switch is ON if the
switch is pressed down on the
right-hand side. The switch is
OFF if the left side is pressed
down.
HARASSMENT SETTING SWITCHES
The Harassment Setting
Switches are the first eight
switches in the switch array.
Each switch has a number to
the right of it that corresponds
with the harassment des-
criptions listed on the foil label
inside the unit.
MODE SETTING SWITCHES
The Mode Setting Switches set the various modes of
operation, such as the amount of time between play-
ing harassment sounds, when the
unit will operate (day only, night
only, or 24 hours), and whether the
unit will operate in the random
mode or normal mode.
Switch
Mode or Function
1
Sets the Time Off Period
2
Sets the Time Off Period
3
Sets the Time the unit plays
4
Sets the Time the unit plays
5
Turns Random Mode On or Off
TIME-OFF SWITCHES
The two Time-Off switches
are located just below the
harassment switches
in the
switch array.When the unit is
set to one of the various Time-Off modes, the unit
will delay a number of seconds or minutes
between recorded sounds. Please note that the
unit will play all of the selected harassments (either
sequentially or non-sequentially, depending on the
Random Mode) then it will go into a delay. The
time the unit stays off depends on the Time-Off
and the Random Mode settings. If the unit is op-
erating in Random Mode, the unit will delay any-
where from the minimum value to the maximum
value for that time-off setting. If the unit is not in
Random Mode, it will delay only the minimum
value. To set the Time Off period (or delay interval),
use the following settings on switches 1 and 2 in
the mode function settings.
Switch 1 Switch 2
Time Off Period
ON
OFF
Short
OFF
ON
Medium
ON
ON
Long
OFF
OFF
Extra Long
Mode
Min
Max
Short
17 sec
50 sec
Medium
1 min
4:15 min
Long
5:00 min
10:00 min
XLong
10 min
30 min
TIME OF OPERATION SWITCHES
The two “Day/24hour/Night” switches are located
just under the Time-Off switches
in the switch
array. ‘Night Mode’ operates
the unit at night and ‘Day
Mode’ operates the unit dur-
ing the day. However, the
photocell that senses the sunlight is susceptible to
bright lights. Take care not to have bright lights
shining towards the unit since this can prevent the
unit from operating properly. In 24-hour mode, the
unit will operate continuously, regardless of the time
of day. To set the Time period for the unit to operate
set switches 3 and 4 in the Mode Function settings
to the following:
Switch 3 Switch 4
Mode
ON
OFF
Day Only
OFF
ON
24-Hour
ON
ON
Night Only
OFF
OFF
also Night Only
RANDOM OPERATION SWITCH
The “Random” switch is the
bottom switch in the switch
array. When operating in
Random Mode, the unit will
randomly play the selected harassments in non-
sequential order. When the unit is not operating in
the Random Mode, the unit will play the selected
harassments in a sequential order. The Random
Mode is recommended to keep critters from
adapting to a preset pattern of sounds. To operate
the unit in Random mode, set switch 5 in Mode
settings
as follows:
Switch 5
Mode
ON
Random mode ON
OFF
Random mode OFF
PROGRAMMING EXAMPLE
Harassment Switches:
Results
1, 3, 5 and 6 to “ON” position
Plays Harrassment
1, 3, 5 & 6
Mode Switches
1 = “OFF” position
2 = “ON” position
(Medium), every 1 to 4 minutes
3 = “ON” position
4 = “OFF” position
Operates during daylight hours only
5 = “ON” position
In random, non-sequential order
VOLUME CONTROL
The unit has a volume control dial on the front panel
of the unit. Turning the dial toward low will result in
reduced sound output and rotating the dial toward
high will result in an increase in sound output.
CAUTION: Take care when turning the dial since the unit may be in
an inactive state when the dial is rotated. It could then reactivate
at a very high level of sound which could be painful to your ears.
HARASSMENT #1
HARASSMENT #2
HARASSMENT #3
HARASSMENT #4
HARASSMENT #5
HARASSMENT #6
HARASSMENT #7
HARASSMENT #8
TIME OFF
DAY/24HR/NIGHT
RANDOM
123
456
7
8
12345
HARASSMENT
Switches (1-8)
HARASSMENT #8
TIME OFF
DAY/24HR/NIGHT
RANDOM
12345
Mode Setting
Switches (1-5)
TIME OFF
DAY/24HR/NIGHT
RANDOM
12345
TIME OFF
DAY/24HR/NIGHT
RANDOM
12345
T ME O
DAY/24HR/NIGHT
RANDOM
2345
HARASSMENT #1
HARASSMENT #2
HARASSMENT #3
HARASSMENT #4
HARASSMENT #5
HARASSMENT #6
HARASSMENT #7
HARASSMENT #8
TIME OFF
DAY/24HR/NIGHT
RANDOM
123
456
7
8
1
2345
