6
INSTRUCTIONS FOR USE
WIRELESS WEATHER STATION
250102 ; 250108
The Instructions is a part of the product and shall be kept for future reference. It contains important
information on the device setting and operation.
1. PACKAGING CONTENT
•
Wireless weather station
•
Single wireless sensor
•
Instructions for Use
2. FUNCTIONS
•
Outdoor and indoor temperature (°C or °F)
•
Indoor humidity (% RH)
•
Saving min. and max.outdoor temperature
•
Calendar (day, month, year, days of week)
•
Clock
•
Alarm clock with a snooze
•
Weather forecast
•
Backlit display
•
RCC – radio controlled clock DCF-77
3. STARTING THE DEVICE
Remove the protective film from the display prior to use.
Battery installation
Note: To avoid operating problems pay attention to polarity of alkaline batteries at inserting them (wrong polarity of
batteries may result in a permanent damage to the device).
Place the wireless sensor nearby the base station.
Open the battery cover on the wireless sensor.
Open the battery cover on the base station.
Place two AAA (LR03) batteries in the wireless sensor.
Put two AA (LR6) batteries in the weather station. A short sound will be emitted once the batteries are
placed in the weather station and all segments of the LED display will flash for 3 seconds. The station will
start synchronisation with the wireless sensor.
Close the battery cover.
Wait 3 minutes until the readings from the wireless sensor are displayed (temperature).
Close the battery cover on the wireless sensor
To read the outdoor temperature and humidity, place the sensor outdoors. The sensor will measure and
send the registered values from its mounting place.
Any time batteries are replaced in the outdoor sensor, a random protection code is sent to the station. Both
devices should synchronise automatically. However, it is recommended to restart the weather station by
removing the batteries for a short while, at replacing the batteries in the sensor. It will allow for restoring
contact with the sensor.
Note: Once all measured values are shown on the display (indoor and outdoor), the wireless sensor can be placed
outdoors and the station in any place. If outdoor measurements do not appear on the weather station, make sure
the sensor is within the station reach or repeat the battery installation procedure. If a key was pressed before all
readings appeared on the display, repeat the battery installation procedure. Prior to another battery installation
wait for at least 10 second to make sure that both the station and the sensor reset correctly.
7
4. PROGRAMMING FUNCTIONS
Radio controlled clock – RCC
The clock is radio synchronised from a transmitter in Mainflingen near Frankfurt and is based on Caesium Atomic
Clock whose deviations do not exceed one second per million years. DCF-77 signal is transmitted at the frequency
of 77.5 MHz and has the reach of 1,500 km. Station 250102 and 250108 receive the signal and transforms it into
legible time. Hence the time displayed on the screen of the clock within DCF-77 signal reach is perfectly accurate.
It is recommended to place the station
in the western window to facilitate receiving the radio signal
At an attempt to receive the signal, symbol will be constantly displayed on the screen, next to the time.
Further setting buttons are blocked. After receiving the signal or after 7 minutes, they will be unlocked.
If the radio signal is not received, the symbol will disappear. To renew the signal search press and hold
WAVE for 5 seconds. The symbol will be shown on the display again.
Once the signal is received, will be displayed all the time.
The weather station can be located in any place indoors.
Note!
The signal shall be received within 24 hours.
If DCF-77 signal is not available, it is possible to set the weather station manually as follows:
Setting the time and date
Press and hold SET for 3-4 seconds until the figure standing for the year starts flashing on the display.
Press “
▲
” or “
▼
“ to set the year.
Press SET the digit standing for the month will start flashing on the display.
Press “
▲
” or “
▼
“ to set the month.
Press SET the digit standing for the day will start flashing on the display.
Press “
▲
” or “
▼
“ to set the day.
Press SET, the data format will begin flashing on the screen, depending on whether you want the station to
display the day first (letter “D” near the number) and the month next (letter “M” near the number), or
inversely.
Press “
▲
” or “
▼
“ to set format of date.
Press SET the names of days will start flashing on the display
Press “
▲
” or “
▼
“ to set the language.
Language
Sunday
Monday
Tuesday
Wednesday
Thursday
Friday
Saturday
German, GE
SO
MO
DI
MI
DO
FR
SA
English EN
SU
MO
TU
WE
TH
FR
SA
Italian IT
DO
LU
MA
ME
GI
VE
SA
French, FR
DI
LU
MA
ME
JE
VE
SA
Dutch. ,NE
ZO
MA
DI
WO
DO
VR
ZA
Spanish ,ES
DO
LU
MA
MI
JU
VI
SA
Danish, DA
SO
MA
TI
ON
TO
FR
LO
Press SET ,
the digit standing for the time zone will start flashing on the display.
Set the time zone with
“
▲
” or “
▼
“
, it can be set within the range of +/- 12 hours.
Press SET, the digit standing for 12/24 hr format will start flashing on the display.
Press “
▲
” or “
▼
“ to set 12/24 hr format,
Press SET the hour digits will start flashing on the display.
Press “
▲
” or “
▼
“ to set the hour.
Dokument pobrany ze strony: sklep.e-szop.pl