1
2
3
4
5
6
7
4
8
9
10
Operating Elements
1.Cutting head
2.Guide rail
3.Pressing rail with finger protection
4.Function switch(temperature control)
5.Indicator elements(LEDs)
6.Laminator infeed
7.Visual positioning aids in cm(lines,angles,scale)
8.ON/OFF switch
9.Anti-blocking slider(for clearing jams)
10.Corner rounder(The function for rounding off
the corners is located on the reverse side of
the devices.)
Operation
Laminator
The laminator can complete hot and cold lamination:
In the case of hot lamination, the lamination foil is adhered together.
In the case of cold lamination, the lamination foil is pressed together.
Select the lamination method according to the material to be laminated.
Note: Only cold lamination should be used for thermopaper and ultrasonic images!
1.Hot laminating
1.1 Connect the power cable to an easily accessible, standard electrical socket.
Caution: Check that the voltage specifications of the unit correspond to that of your power supply
network (220 - 240V, 50Hz).
1.2 Use the on/off switch on the right of the appliance to switch on:"HOT", the red display lamp shows.
1.3 The drive motor for the transport rollers starts up. The correct operating temperature is reached
after about 3-5 minutes and the green display lamp shows.
1.4 Insert the document to be laminated in the pouches so that there is a margin of approx. 3 - 5 mm
to the edge of the foil on all sides.
Caution: Only use foil intended for hot laminating.
1.5 Insert the foil containing the document in the laminator's insertion slot. Insert the ready closed
side of the pouch first.
Note: To prevent the laminating foil from creasing, never insert the open end of the foil pocket in the
insertion slot of the laminator first. When inserting the foil, observe the instructions on the
insertion slot. The laminating process occurs automatically.
Caution: The lamination foil is very hot and soft when ejected following lamination. Therefore, handle
the laminated document with due care!
Note: To flatten and smoothen the laminated product, place a book or similar heavy, flat object on it.
1.6 When you have completed the laminating process, turn the function switch to the right in COLD
position and remove the power plug from the power socket. Let the device cool down before
packing it away, for example.
Caution: The device is very hot directly after laminating! Risk of injury!
2. Cold laminating
Attention: If you have just finished using the laminator for hot laminating, you must let the laminator
cool down. It takes about 30 minutes to cool down sufficiently.
2.1 Turn the function switch to the right in the COLD position.
Note: Only use cold lamination foil for cold laminating.
2.2 Remove the protective foil from the lamination foil.
2.3 Insert the document to be laminated in the lamination foil so that there is a margin of approx.
3 - 5 mm to the edge of the foil on all sides.
2.4 Guide the laminating foil containing the document to be laminated in the laminator infeed with the
closed side first. The laminating process occurs automatically.
Note: To prevent the lamination foil from creasing, never feed the open side of the lamination foil first
in the laminator infeed. When inserting the lamination foil, observe the instructions on the
infeed slot.
3.Clearing jammed lamination foil
The device is equipped with an ABS switch (anti-blocking sliding switch) to clear foil jams quickly.
Proceed as follows if the lamination foil jams:
3.1 Switch the device off: Set the On/Off switch to OFF.
3.2 Slide the ABS switch fully to the left.
3.3 Hold the laminator firmly and pull the lamination foil together with the document to be laminated
out of the laminator's infeed.
3.4 Slide the ABS switch fully to the right.
3.5 Clean the transport rollers of any deposits and residual adhesive by inserting a folded piece of
paper in the laminator infeed, refer to Chapter "Cleaning the transport rollers".
Note: If foil jams occur repeatedly or jammed foil cannot be removed from the laminator, please
contact our hotline (refer to Guarantee).
Trimmer
The trimmer can be used to cut paper, card, photo paper and lamination foil.
1.Selecting the type of cut
The trimmer is equipped to complete three types of cut:
straight cut,
wave cut,
perforation cut.
Note: The blades are accommodated in protective housing.
Select the type of cut you require,see Fig.1:
1.1 Pull the setting lock on the cutting head upwards to the OPEN position.
1.2 Turn the rotating knob for the cut until the symbol related to the required cut is at the top.
1.3 Press the setting lock on the cutting head downwards to the LOCK position.
2.Cutting material
2.1 Place the device on a stable, level surface with the cutting head facing up.
2.2 Slide the cutting head to one side of the guide rail
2.3 Slide the material to be cut under the transparent pressing rail at the required position.
Note: Observe the permissible quantity of material which may be cut, refer to Chapter “Intended Use”
or “Technical Data”.
Note: The visual positioning aids simplify correct alignment of the material to
be cut.
2.4 Hold the material to be cut firmly with one hand so that it cannot slip when
cut. Otherwise, the cut may be inaccurate.
2.5 To complete the cut, press the cutting head down and slide it along the
guide rail to the other side, refer to Fig. 2.
Note: To prevent a faulty cutting edge, do not run the cutting head back again
but remove the cut material directly after completing the cut.
