Biostar NF4ST-A9 Bios Setup Manual Download Page 27

Page: 27 / 28

NF4ST-A9

8 PC Health Status

Figure 8. PC Health Status

Chassis Open Warning

This item allows you to enable or disable Chassis Open Warning beep.

The Choices: Disabled

(Default), Enabled.

Shutdown Temperature

This item allows you to set up the CPU shutdown Temperature. This item only effective
under Windows 98 ACPI mode.

The Choices: Disabled

(default), 60

℃

/140F, 65

℃

/149F, 70

℃

/158F, 75

℃

/167F.

Show H/W Monitor in POST

If your computer contains a monitoring system, it will show PC health status during POST
stage. The item offers several delay time for you to choose.

The Choices: Enabled

(default), Disabled.

CPU Vcore/ +1.5V+3.3V/ +5.0V/ +12.0V/+5V/ 5VSB/ Voltage Battery

Detect the system’s voltage status automatically.

CPU Temperature

This field displays the current temperature of the CPU.

Current CPU FAN Speed

Summary of Contents for NF4ST-A9





























Search results

Summary of Contents for NF4ST-A9

Reviews:

Related manuals for NF4ST-A9

Brands by name

Popular brands

Biostar NF4ST-A9, Bios Setup Manual

Search results

Summary of Contents for NF4ST-A9

Reviews:

Related manuals for NF4ST-A9

Brands by name

Popular brands