background image

M7VIW-D BIOS Setup 

 

22

 
There are four options of Power Management, three of which have fixed mode settings 

Min. Power Saving 

Minimum power management. 
Suspend Mode = 1 hr. 
HDD Power Down = 15    min 
 

Max. Power Saving 

Maximum power management only available for sl CPU’s. 
Suspend Mode = 1 min. 
HDD Power Down = 1 min. 
 

User Defined 

(default)

 

Allows you to set each mode individually.   
When not disabled, each of the ranges are from 1 min. to 1 hr. except for HDD 
Power Down which ranges from 1 min. to 15 min. and disable.

 

 

 

HDD Power Down 

When enabled, the hard disk drive will power down and after a set time of system inactivity. 
All other devices remain active. 

The Choices: Disabled

 (default), 1 Min, 2 Min, 3 Min, 4 Min, 5 Min, 6 Min, 7 Min, 8 Min, 

9 Min, 10 Min, 11 Min, 12 Min, 13 Min, 14 Min, 15Min.

 

 

Suspend Mode 

The item allows you to select the suspend type under ACPI operating system. 

The Choices: Disabled

 (default), 1 Min, 2 Min, 4 Min, 6 Min, 8 Min, 10 Min, 20 Min, 30 

Min, 40 Min, 1 Hour.

 

 

Video Off Option 

This field determines when to activate the video off feature for monitor power   
management. 

The Choices: Suspend

Off 

(default), Always on.

 

 

Video Off Method 

This option determines the manner in which the monitor is goes blank. 

V/H SYNC+Blank

 (default)

 

 This selection will cause the system to turn off the vertical and horizontal 
synchronization ports and write blanks to the video buffer. 

Blank Screen 

Summary of Contents for M7VIW-D

































Reviews: