background image

I945G-M7 

18

 

CHAPTER 4: USEFUL HELP 

4.1 A

WARD 

BIOS

 

B

EEP 

C

ODE

 

Beep Sound 

Meaning 

One long beep followed by two short 
beeps 

Video card not found or video card 
memory bad 

High-low siren sound 

CPU overheated   
System will shut down automatically   

One Short beep when system boot-up

No error found during POST 

Long beeps every other second 

No DRAM detected or install 

4.2 E

XTRA 

I

NFORMATION

 

A. BIOS 

Update 

After you fail to update BIOS or BIOS is invaded by virus, the 
Boot-Block function will help to restore BIOS. If the following message 
is shown after boot-up the system, it means the BIOS contents are 
corrupted. 

 

 

In this Case, please follow the procedure below to restore the BIOS: 

1.  Make a bootable floppy disk. 

2.  Download the Flash Utility “AWDFLASH.exe” from the Biostar 

website: 

www.biostar.com.tw

 

3.  Confirm motherboard model and download the respectively 

BIOS from Biostar website. 

4.  Copy “AWDFLASH.exe” and respectively BIOS into floppy disk. 

5.  Insert the bootable disk into floppy drive and press Enter. 

6.  System will boo-up to DOS prompt. 

7. Type 

“Awdflash xxxx.bf/sn/py/r”

 in DOS prompt. 

8.  System will update BIOS automatically and restart. 

9.  The BIOS has been recovered and will work properly. 

Summary of Contents for I945G-M7
































Reviews: