◆
Packing List
The box should contain the DVT12S2 and below accessories:
DVT12S2 Body
DVT12S2
Quick Installation Guide
Power cable
◇
Packing List
Ɣ'976%RG\
Ɣ
Power cable
ƔPLQL6$6FDEOH0HWHU
Ɣ4XLFN,QVWDOODWLRQ*XLGH7KLVGRFXPHQW
◆
Name and Function of each part
＜
DVT12S2Front
＞
①
POWER Button
Power ON /OFF Switch
②
POWER LED
BLUE: On, power up indication
③
HDD Access / Fail*
LED
BLUE : On, disk drive inserted
BLUE Flash: Drive Activity
Amber ON : Drive Fail, Locate, or Rebuild
Amber LED depends on RAID or HBA implementation
④ System Fail LED
Amber ON: Indicate any system fail such
as over temperature, fan fail or expander fail
⑤ Fan Fail LED
Internal Fan 1 or Fan 2 Fail. Refer to HBA, RAID GUI
⑥
Mute Button
Turn off the buzzer alarm
⑦
miniSAS Host
SFF8088 connector for Host connection
⑧
miniSAS Expansion
SFF8088 connector for Expansion
⑨
Power Inlet
AC Power Inlet, Full range AC 90-260V
Begin to use
1.Find the miniSAS cable inside the package connecting it to miniSAS
RI+RVW+%$RU5$,'+%$5HIHUWRQH[WSDJHUHDUYLHZRIWKHHQFORVXUH
2.Connect power cord to the AC inlet
3.Push power button at front side of the chassis
4.Power on your host computer and start to configure your RAID HBA
5.If you had more than one DVT12S2 to cascade,
connect the expansion port to the host of next DVT12S2.
For Disk drive installation if needed,
Follow the below instruction to install or replace a disk drive.
Step 1.
Loosen the left side rear screws
UHDUYLHZDQGRSHQWKHVLGHSDQHO
Step 2.
Use hand or screw driver to loosen
the thumb screw of disk drive tray.
Step 3.
Prepare a flat operating table for following operation.
Put the disk drive perpendiculous to the flat table with the drive connector
WRZDUGERWWRPGULYHFRQQHFWRUVLGHIDFLQJ\RX
With thumb screw of drive tray on left hand side, slide down the tray carefully
till it touches down the flat table.
Step 4.
Get four screws from the screw bag
and tightly screw them all
◆
Installation Guide
③
④
⑤
⑥
①
②
＜
DVT12S2Rear
＞
⑧
⑦
⑨
Drive numeration label is attached
on side panel as below.
PLQL6$6FDEOH0HWHU
Quick Installation Guide
−
SAS6G model
−
DVT12S2
This Quick Installation Guide(QIG) describes the packing content and
installation guide line for DVT12S2 model.
BIOS and its resellers are not liable for any
data or information lost or possible software
issue to use the product. We do not take any
responsibility of damage and/or systemmalfunc-
tion due to our product / storage device failure
or for any of the problems caused as a result It
is recommended to always backup your data.
◆
Introduction
Attention
Compact and Large Capacity Desktop SAS JBOD
Up to 12 Hot-swappable 3.5” SAS or SATA Drives
DVT12S2 Quick Installation Guide – SAS 6G model-
DVT12S2model
Quick Installation Guide
Drive Fault LEDs can also be found on backplane for each drive when chassis is opened for drive replacement