background image

display which is always displayed while batteries are in
the remote) and the unit will shut off.

Note: It is normal for the heater to cycle on and off as it
maintains the preset temperature.  To prevent the unit from
cycling, you need to raise the thermostat setting.

ADJUSTING SET TEMP:

1.  When in “Auto” mode, press the (+) button on the 

remote.  The “Set” number will increase with each 
press.  Hold the button down to scroll.  The minimum 
temp is 55ºF and the maximum is 85ºF. The unit scrolls 
one digit at a time in a continuous loop. 55º, 56º…, 84º,
85º, 55º, 56º….  

2.  When in “Auto” mode, press the (-) button on the 

remote to decrease the “Set” temperature/humid. The 
unit scrolls one digit at a time in a continuous loop.

UNIT OPERATION WITHOUT REMOTE

A.  Remote and Unit are OFF:

1.  Press the Mode button on the unit the first time.  The 

"Low" light illuminates and the unit runs in "Low" mode.
The power light turns on.

2.  Press the Mode button a second time to run in "High" 

mode (1500 Watts). 

3.  Press the Mode button a third time and the unit shuts 

off. 

Note: The "auto" light only illuminates when the unit is set
to "auto" mode by the remote.

B.  Remote is ON and Unit is ON:

1.  Press the Mode button on the unit.  The unit will then 

switch "Modes"; either from "Low" to "High", "High" to 
"Off"  or "Auto" to "Off" . The unit’s lights will reflect the 
change.  The Remote will display a different mode – the
mode in which it was left.  If a button is pressed on the 
Remote, the Remote’s signal will override the "Mode" 
on the unit and the two will be back in sync.

TIMER FUNCTION:

To turn unit off while remote and unit are on (in low, high,
auto state).

1) Hold mode button for 2 seconds to unlock remote.

2)  Push + and - together.

2.1) "timer" turns on. 1 Hr appears on the screen. 

2.2)  the current mode will remain displayed on the 

screen ("low" or "high" or "auto")

3)  Push + or - to adjust the number of hours the unit will 

run before it shuts itself off.

3.1) you can choose from; 1, 2, 3, 4, 5, 6, 7, 8 hours

3.2) 1 through 8 will scroll in a continuous loop

4)  After you have made your selection,  "timer" flashes for 

5 seconds after last button push of + or - then goes 
back to previous mode

4.1) "timer" remains lit to show the timer function has 

been set.

5)  At any time if you unlock the remote and push the 

mode button to turn the unit off the timer setting 
will be erased and "timer" will disappear from the 
remote.  To check how much time is remaining, press 
and hold the + and – buttons simultaneously.

To turn unit on while remote and unit are off (only ambient
temp is displayed on remote). 

This function is meant for a person to preheat a room by
setting the timer. For Example: Locating the unit in the
bedroom and setting the timer at 8AM for 12hrs, this
allows the room to preheat for 2 hours. The unit will turn
on at 8PM and shut off at 10PM. Your room will be 
preheated before you go to bed at 10PM.

low

high

mode

auto

Figure 2

6

7

Summary of Contents for GALILEO BCH4138














Reviews: