ASSEMBLY INSTRUCTIONS
NOTE:
MAKE SURE YOU REMOVE ALL CONTENTS OF THE
PACKAGE. PLEASE CHECK PACKAGING MATERIALS FOR
PARTS THAT COULD BE REQUIRED TO OPERATE YOUR FAN.
Tools required: Phillips head screw driver (not
included)
Assembly time: 5–10 minutes
1. Insert the lower end of the outer pole through the
hole in the center of base and twist clockwise into
position.
2. Insert the threaded end of the T-shaped locking lever
into the hole of the washer and through the base.
3. Turn the T-shaped locking lever clockwise to securely
attach the pole to the base.
4. Set the base on the floor.
5. Loosen fan post screw and insert the motor housing
over top of extension pole. Tighten fan post screw.
6. Line up the slots of the rear grill with the notches on
the motor housing assembly.
7. Secure rear grill to motor housing assembly with rear
grill mounting nut. Turn clockwise to tighten.
8. Slide blade over motor shaft.
9. Secure fan blade to motor shaft with the blade cap.
Turn counter-clockwise to tighten.
10. Remove the grill screw and nut located on the bottom
of the grill.
11. Slide the front grill over the rear grill.
12. Replace grill screw and nut and tighten with screw
driver.
13. Attach the misting hose clip onto the outer pole (see
Figure 1).
OPERATING INSTRUCTIONS
1. Set the fan on a dry and level surface.
2. Plug the cord into a standard 120 volt AC outlet.
3. The fan controls are located on the back of the Motor
Housing. Select Fan Speed =
0
- Off,
3
- High,
2
- Medium,
1
- Low.
4. Push, Pull Oscillation Knob (
) = Oscillation
On, Off.
MISTING KIT ASSEMBLY INSTRUCTIONS
1. Turn the Fan Speed Knob to the (
0
) position.
2. Attach the end of the Misting Hose Connector to a
standard garden hose and turn on the water. Turn the
switch on the connector to ON position (see figure 2).
3. Turn the Adjustable Mist Knob (see Figure 3) on front
grill to open the desired number of nozzles for
misting (2-3-1).
4. Turn the fan on and enjoy.
ADJUSTMENT INSTRUCTIONS
Tilt Adjustment
Follow these instructions to tilt the fan head for upward
angle air movement.
STEP 1: To change the tilting angle of the fan head;
simply loosen the tilt adjustment knob.
STEP 2: Move the fan head to the desired angle, and
firmly tighten the knob to lock in place.
Height Adjustment
Follow these instructions to adjust the height of the fan.
STEP 1: Turn the height adjustment collar counter-
clockwise to loosen pole.
STEP 2: Adjust the extension pole to the desired height,
and firmly tighten the height adjustment collar in
a clockwise direction.
CLEANING/MAINTENANCE
INSTRUCTIONS
Follow these instructions to correctly and safely care for
your fan.
REPLACEABLE FUSE
If your (5 Amp, 125 Volt) replaceable fuse blows, please
visit our website at www.bionaire.com for information on
how to order a new fuse. Follow the below instructions to
replace the fuse on the power cord.
User Servicing Instructions
1. Unplug your fan. Grasp plug and remove from the
receptacle or other outlet device. Do not unplug by
pulling on cord.
2. Locate the fuse holder on the power cord. Use
screwdriver to remove the fuse cover and take out
the O-ring (see Figure 4).
Note:
Ensure that fuse cover is completely open
before attempting to remove fuse.
3. Remove fuse carefully by using a small screwdriver
to pry the fuse out of the compartment by the metal
ends of the fuse (see Figure 4).
4. Place plug on a solid, flat surface. Insert new 5 Amp,
125 Volt fuse into fuse compartment and use a small
screwdriver to secure the metal ends of the fuse into
the compartment.
Caution:
Risk of fire. Replace fuse only with 5 Amp,
125 Volt fuse.
5. Replace the
O-ring, close the
fuse cover in place
and secure with
the 2 screws (see
Figure 4). If fuse
cover is difficult to
close, make sure
fuse is secured in
place completely
by pressing down
on metal ends of
the fuse.
6. Risk of fire. Do
not replace
attachment cord/plug. Contains a safety device (fuse)
that should not be removed. Discard product if the
attachment cord/plug is damaged.
FAN CLEANING
• Always unplug the fan before cleaning.
• Do not allow water to drip on or enter into fan housing.
• Be sure to use a soft cloth moistened with or without
a mild soap solution.
• Do not use any of the following as a cleaner:
gasoline, thinner, or benzene.
Fan Blade Cleaning
1. To access the fan blade, remove the front grill and
blade cap.
2. Clean the fan blade, front and rear grills with a soft
moist cloth.
3. Replace blade, tighten blade cap, and securely fasten
the front grill (see Assembly Instructions to ensure
the fan blade, front and rear grills are assembled
properly).
Fan Head, Base and Pole Cleaning
Using a soft, moist cloth with or without a mild soap
solution carefully clean the fan base, pole and head.
Please use caution around the motor housing area. Do
not allow the motor or other electrical components to be
exposed to water.
FAN STORAGE INSTRUCTIONS
• The fan comes with a cover to protect the fan head from
weather as it is built to be used and stored outdoors.
• Store your fan in the original box or an appropriately
sized box.
• Protect the fan head from dust.
• Store your fan in a dry location.
P L E A S E R E A D A N D S AV E T H E S E
I M P O RTA N T S A F E T Y I N S T R U C T I O N S
F E AT U R E S - O P E R AT I O N S
When using electrical appliances, basic safety precautions
should always be taken including the following:
1. Read all instructions before using this appliance.
2. Use fan only for purposes described in the instruction
manual.
3. To protect against electrical shock do not immerse
unit, plug or cord in water or spray with liquids and
plug the appliance directly into a 120V AC electrical
outlet.
4. Close supervision is necessary when any appliance is
used by or near children.
5. Unplug from outlet when not in use, when moving
fan from one location to another, before putting on
or taking off parts and before cleaning.
6. Avoid contact with moving parts.
7. Do not operate in the presence of explosive and/or
flammable fumes.
8. To avoid fire hazard, NEVER place the cord under
rugs or any parts near an open flame, cooking or
other heating appliance.
9. Do not operate any appliance with a damaged cord
or plug after the appliance malfunctions, or has been
dropped/damaged in any manner. Discard fan or
return to an authorized service facility for
examination and/or repair.
10. Do not run cord under carpeting. Do not cover cord
with throw rugs, runner, or similar coverings. Do not
route cord under furniture or appliances. Arrange
cord away from traffic area and where it will not be
tripped over.
11. The use of attachments not recommended or sold by
the appliance manufacturer may cause hazards.
12. Do not let the cord hang over the edge of a table,
counter or come in contact with hot surfaces or leave
exposed to high traffic areas.
13. To disconnect, grip plug and pull from wall outlet.
Never yank on cord.
14. Always use on a dry, level surface.
15. Do not operate fan until fully assembled with all
parts properly in place.
16. This product is intended for household use ONLY and
not for commercial or industrial applications.
17.
WARNING:
To reduce the risk of electrical shock
and injury to persons, do not use in window.
18.
WARNING:
To reduce the risk of fire or electric
shock, do not use this fan with any solid-state speed
control device.
19. This product employs overload protection (fuse). A
blown fuse indicates an overload or short-circuit
situation. If the fuse blows, unplug the product from
the outlet. Replace the fuse as per the user servicing
instructions (follow product marking for proper fuse
rating) and check the product. If the replacement
fuse blows, a short circuit may be present and the
product should be discarded or returned to an
authorized service facility for examination and/or
repair.
PLEASE READ AND SAVE
THESE IMPORTANT SAFETY
INSTRUCTIONS
CONSUMER SAFETY INFORMATION
NOTE:
This is an electrical appliance and requires
attention when in use.
NOTE:
THIS PRODUCT IS EQUIPPED WITH A 3-PRONG PLUG.
F E AT U R E S - O P E R AT I O N S
C L E A N I N G / M A I N T E N A N C E
Figure 3
Adjustable
Mist Knob
Close-up of Adjustable Mist Knob
Nozzles (3)
Figure 4
Fuse Holder
Fuse Cover
O-ring
Fuse
This product is for use on 120 volts. The cord has a plug (A) as shown. An
adapter (C) (not included) is available for connecting three-blade grounding-
type plugs to two-slot receptacles (B). The green grounding lug extending
from the adapter must be connected to a permanent ground such as a
properly grounded outlet box. The adapter should not be used if a three-slot
grounded receptacle is available.
CAUTION:
Use Only with GFCI Protected Receptacles.
Figure 2
Misting Hose
Misting Hose
Connector
Switch
SWITCH ON
If you have any questions regarding your product or
would like to learn more about other Bionaire
®
products, please contact our Consumer Service
Department at 1-800-253-2764 or visit our website at
www.bionaire.com. For inquiries regarding recycling
and proper disposal of this product, please contact your
local waste management facility.
Figure 1
A
B
D E
G
I J K
V
M
T
U
X
L
F
H
A. Logo Plate/Adjustable
Mist Knob
B. Misting Nozzles (3)
C. Front Grill
D. Blade Cap
E. Fan Blade
F. Rear Grill Mounting
Nut
G. Rear Grill
H. Motor Shaft
I. Motor Housing
J. Oscillation Knob
K. Switch Knob
L. Tilt Adjustment Knob
M. Fan Post Screw
N. Extension Pole
O. Height Adjustment
Collar
P. Outer Pole
Q. Base
R. Washer
S. T-shaped Locking
Lever
T. Misting Hose
U. Misting Hose
Connector
V. Power Cord
W. Fuse Holder
X. Grill Screw and Nut
Y. Misting Hose Clip
O
Y
P
Q
R
S
C
N
W
BSF1613A-BCU_15EM1.indd 2
2/2/15 9:44 AM
