BDWLF1609-IN
Fig. 1
Fig. 2
Fig. 3
1. Front Guard
2. Guard loop
3. Guard Locking Screw/Nut
4. Blade Retaining Nut
5. Small Blade
6. Large Blade
7. Guard Retaining Nut
8. Rear Guard
9. Handle
10. Motor Shaft
11. Motor Case
12. Installation Plate
13. Thumbscrew
14. Control Panel
15. Cords
BDWLF1609-IN
PLEASE READ AND SAVE THESE
IMPORTANT INSTRUCTIONS
1. Read all instructions before using this
appliance.
2. To avoid fire or shock hazard, plug the
appliance directly into an appropriate
electrical outlet.
3. Keep the power cord out of heavy
traffic areas. To avoid fire hazard,
NEVER
put the power cord under
rugs, near heat registers, radiators,
stoves, or heaters.
4. To protect against electrical hazards,
DO NOT
immerse the appliance in
water or other liquids. Do not use
near water.
5.
NEVER
drop or insert any objects into
the openings of the unit.
6. Do not operate any appliance with a
damaged power cord or plug. If the motor
fails to operate or the unit has been
dropped or damaged in any manner,
return appliance to manufacturer for
examination and/or repair.
7.
DO NOT
use outdoors.
8.
NEVER
place on a soft surface such
as a bed or sofa as this could cause
the unit to tip over and block the air
inlet or outlet grills.
9.
DO NOT
place anything on top of unit.
10.
WARNING:
To reduce the risk of fire
or electric shock,
DO NOT
use this
appliance with any solid-state speed
control device.
11.
CAUTION:
In order to avoid a hazard
due to inadvertent resetting of the
thermal cutout, this appliance must not
be supplied through an external
switching device, such as a timer, or
connected to a circuit that is regularly
switched on and off by the utility.
12.This appliance is not intended for use by
persons (including children) with reduced
physical, sensory or mental capabilities,
lack of experience and knowledge,
unless they have been given supervision
or instruction concerning use of the
appliance by a person responsible for
their safety. Children should be
supervised to ensure that they do not
play with the appliance.
13.This product is not desgned or intended
to be used with an extension cord.
ASSEMBLY INSTRUCTIONS
1. Remove the blade retaining nut
(turning clockwise) while holding motor
shaft. Then remove the guard retaining
nut (turning counter-clockwise). Take
off the motor shaft sleeve protector
and discard.
2. Set the rear guard in the proper
position (carry handle topmost) on the
motor assembly. Make sure that the
pins on the rear guard align with the
pins on the motor assembly. Then
screw on the guard retaining nut
(turning clockwise) until tight.
3. Install the large blade onto the shaft of
the motor assembly. Then install the
small blade. The flat area of the “D”
on the blade should align with the flat
area of the “D” on the motor shaft.
Screw on the blade retaining nut
(turning counter-clockwise) until tight.
4. Open the guard locking screw/nut.
Place the guard loop on the rear guard
with the guard locking screw/nut at the
bottom. Assemble the front guard on
guard loop until all sides snap. Rotate
the front guard until the Bionaire logo
is horizontal.
5. Secure both guards firmly by fitting
and tightening the guard locking
screw/nut.
INSTALLING INSTRUCTIONS
1. Select a suitable spot on the wall
(away from curtains, draperies, or heat
sources) where you want to mount the
fan and in close proximity to the power
supply.
2. Remove the installation plate and use
it as a template to mark holes in the
wall. Note that the fan must be
mounted vertically.
ENGLISH
11
10
8
7
5
4
2
1
3
13
12
14
15
9
6
11
10
8
7
5
4
2
1
3
13
12
14
15
9
6
HINDI
