the
Frost Guard
setting (
), the heater will
turn on automatically when the room
temperature drops below 5°C.
NOTE:
It is normal for the heater to cycle on
and off to maintain the preset temperature.
Raise the thermostat setting to prevent the
heater from cycling. When the preset
temperature is reached or when the heater is
shut off, the fan will run for 15 seconds without
heat. This cool down process ensures an
accurate and consistent temperature reading.
NOTE:
To shut the heater off at any setting,
press the Power Button (
) until all indicator
lights go off. The heater will cool down for 15
seconds, and the
Fan Only
indicator light will
blink in Amber until cool down is completed. The
digital thermostat has memory; it will remember
the last temperature setting before the heater is
turned off. However, if the heater is unplugged,
the digital thermostat will no longer remember
the previous temperature setting. You will need
to reset the digital thermostat if the heater is
unplugged.
– Oscillation
Press the Oscillation Button (
) to activate or
stop the oscillation feature.
NOTE:
Please do not manually turn the heater
on the base. It is designed to turn only by
motorized oscillation.
– Timer
This heater is equipped with 12-Hour Auto Shut-
off Timer feature. This allows you to program
your heater to shut off automatically after
running for 4-hour, 8-hour or 12-hour intervals.
1. Press the Timer Button (
) once. The
indicator light will begin to blink for 5
seconds.
2. Turn the Dial Wheel to cycle through the
below sequence:
3. Select your desired interval for the heater to
shut-off automatically. The corresponding
hour indicator light will illuminate, the Timer
indicator light will stop blinking and become
illuminate in 3 seconds to indicate that the
selected timer is activated.
4. To cancel the Timer feature, press the Timer
Button (
) twice within 5 seconds, and all
Timer indicator lights will go off.
NOTE:
The timer does not work with the Frost
Guard Setting.
CLEANING/MAINTENANCE
Always unplug the heater before cleaning and
allow the heater to cool down.
1. Clean the unit with a soft cloth moistened
with a mild soap and water solution.
2. NEVER use abrasive or flammable solvents
to clean the unit.
3. After cleaning, be sure to completely dry the
unit with a cloth or towel.
4. Store heater in a cool, dry location.
5. It is recommended that you store the unit in
its original carton.
TIP:
Over time, dust may accumulate on
the front grills. This can be removed by
wiping the unit with a damp cloth.
AUTO SAFETY SHUT-OFF
This heater is equipped with a technologically-
advanced safety system that requires the user to
reset the heater if there is a potential overheat
situation. When a potential overheat temperature
is reached, the system will automatically shut the
heater off. It can only resume operation when
the user resets the unit.
If the heater shuts down and the Power
Light is flashing:
1. Stand the heater upright.
2. Unplug the heater and allow 30 minutes for
the heater to cool down.
3. After 30 minutes plug the heater in and
operate normally.
4. If the heater does not work normally, repeat
steps 1, 2 and 3 again.
NOTE:
If the heater is plugged in again and
Power On/Off Button is pressed within the
30-minute cool down period, heater will run at
Max Heat (
2
) setting, but shut down in 2
seconds with the Power Light flashing. Please
repeat the above 4 steps to reset the heater
again and ensure to allow sufficient time for the
thermostat to cool down.
Tip Over Shut-Off:
When the unit is accidentally knocked over, it will
instantly shut off and the Power Light will flash.
The unit may also shut off if it is moved or
bumped. To reset, simply place the heater in an
upright position, the Power Light will stop
flashing and it will operate normally.
NOTE:
If unit does not turn on when placed in
the upright position, press Power On/Off Button
once and heater will resume operation.
5
BCH9210-LA_10MLM1.indd 5
BCH9210-LA_10MLM1.indd 5
6/24/10 8:17 AM
6/24/10 8:17 AM
