5
2
ADDITIONAL FEATURES
Setting the Nightlight: In the sunset mode, you can have the light stop
dimming when it reaches approximately 5% intensity, for use as a nightlight.
Press the PROGRAM button 11 times until the display reads NITELITE OFF
or NITELITE ON. Then press the + or - buttons to activate or deactivate the
nightlight.
Activating the Security Mode: This mode is useful when you are away on
vacation and you wish to give the appearance that someone is home. To turn on
the Security Mode, press the PROGRAM button 12 times so the display reads
SECURITY OFF. Press the + or - button and the display will switch to
SECURITY ON indicating that the mode is activated. The clock will come on
and off randomly between 4 p.m. and 11 p.m. When this function is set, and
you’ve exited the programming mode, the main display will read SECURITY.
To exit the security mode upon your return, push any button and SECURITY
should no longer be displayed.
Using the Demonstration Mode: To set or cancel the Demo Mode, see “Setting
the Speed of the SunRise Wake-Up.” Once activated, the display reads DEMO
MODE. This puts the clock in high speed demonstration mode so you can
create a speedy sunrise over just 100 seconds. Push the ALARM button OUT
(on), then hold the PROGRAM button in while pressing the + button at the same
time. Likewise, if you have the light on, and would like to demonstrate the
sunset feature, press the ALARM button IN (off) then press it OUT (on). The
light will fade out over the next 100 seconds.
ACTIVATING THE ALARM
After you have set the time you wish the alarm to go off the next morning, push
the ALARM button so it is OUT (on). The display will show the Alarm Set sun
symbol (
☼
) and the Alarm Time you chose will be displayed for a few seconds.
If the light is on when you enable the alarm, it will slowly fade out, or you can
turn it off right away by pressing and holding the – button until the light is out.
Using the Snooze Feature: To “snooze” the alarm, press the minus button while
the alarm is beeping. The beeper will stop sounding for about 9 minutes. If you
would also like the sunrise to begin again, then continue pressing the minus
button until the light has gone all the way off. Over the next 9 minutes, the light
will gradually brighten (this will occur at a quicker rate than the originally
programmed SunRise time) and finally the beeper will sound again.
Turning off the Alarm: If you want to turn off the alarm after you wake, push
the ALARM button IN (off). The beeping will stop but the light will remain
illuminated until you shut it off. If the alarm is not turned off manually, the
beeper and light will both automatically shut off after about fifteen minutes.
Programming the Clock: Press the PROGRAM (P) button to enter the clock’s
menu and change any of the clock settings. NOTE: The menu is not accessible
if the ALARM (
☼
) button is up (on), so always make sure the ALARM button
is IN (off) when you want to program the clock. The text display below the time
digits will show the setting you are changing and what the current status is.
Change the setting using the PLUS button (+) and MINUS button (-). Once you
have completed a setting, you can press the PROGRAM (P) button again to
adjust another setting, or simply wait for approximately 12 seconds and the
clock will exit the menu automatically and go back to displaying the time.
Programming Table*
P Button
Presses
DISPLAY RESULT
(First setting in bold is the default)
1
ALARM TIME > 7:00 A.M.
2
TIME > 1:00 P.M.
3
12 HOUR > 24 HOUR
4
BEEP ON > BEEP OFF
5
DISPLAY AUTO > DISPLAY HIGH
6
FADEUP 30 > 45 > 60 > DEMO > 15
7
FADEDOWN 30 > 45 > 60 > 15
8
SOUND AUTO > SOUND PERM > OFF
9
OCEAN WAVES > WHITE NOISE > etc.
10
VOLUME 7 (adjusts from 1 to 14)
11
NITELITE OFF > NITELITE ON
12
SECURITY OFF > SECURITY ON
13
(reverts to normal operation)
*Programming settings are memorized by the clock, but if the power goes out or
the clock is unplugged for a few minutes, you will not need to reset the clock.
Setting the Wake-Up Alarm Time: Press the PROGRAM (P) button once, so
the display reads ALARM TIME. Then adjust the alarm time with + and -
buttons until desired time is set. Holding in the + or - button down will cause
the time to change rapidly.
Setting the Time: Press the PROGRAM (P) button twice. The display should
read TIME. Then use the + and - buttons to adjust the time. The time moves
rapidly if the + or - button is held in.
