background image

Safety Instructions

IMPORTANT SAFETYGUARDS

  

  When using electrical products, especially when children are present,  

    basic safety precautions should always be followed.

READ ALL INSTRUCTIONS BEFORE USING

    

●  

In the case 120V 60Hz : Power supply must be a 15 Amp GFCI outlet.

    

●  

The electrical cord must be connected to a GFCI outlet.

    

●  

The GFCL outlet should be 1ft. above the floor.

    

● 

 Install only in well-ventilated areas to avoid excess humidity.

    

●  

Do not install in narrow toilet stalls or in shower stalls.

    

●  

Install only where direct contact with water is minimized.

    

●  

Do not install near any heat source.

    

●  

Avoid using extension cords if possible. Consult with a certified electrician where extension 

      cords are necessary.

DANGER – To reduce the risk of electrocution:

    

● 

 Do not use while bathing.

    

●  

Do not place or store product where it can fall or be pulled into a tub or sink.

    

●  

Do not place in or drop into water or other liquid.

    

●  

Do not reach for a product that has fallen into water.  Unplug immediately.

GROUNDING INSTRUCTION

DANGER - Improper use of the grounding plug can result in a risk of electric shock.

This product has a three-prong grounding plug, which must be plugged into an outlet that is properly installed and 

grounded. In the event of an electrical short circuit, grounding reduces the risk of electric shock by providing an escape 

wire for the electric current. If repair or replacement of the cord or plug is necessary do not connect the grounding wire 

to either flat blade terminal. 

The wire with insulation having an outer surface that is green with or without yellow stripesis the grounding wire. 

Check with a qualified electrician or service person if the grounding instructions are not completely understood, 

or if in doubt as to whether the product is properly grounded.
This product is for use on a nominal 120V circuit, and has a grounding plug that looks like the plug illustrated in sketch 

A in Figure 1.

A temporary adapter, which looks like the adapter illustrated in sketches Band C, may be used to connect this plug 

to a 2-pole receptacle as shown in sketch B if a properly grounded outlet is not available.
The temporary adapter should be used only until a properly grounded outlet (sketch A) can be installed by a 

qualified electrician. 

The green colored rigid ear, lug, or the like extending from the adapter must be connected to a permanent ground 

such as a properly grounded outlet box cover. Whenever the adapter is used, it must be held in place by the screw.

WARNING – To reduce the risk of burns, electrocution, 

                      fire or  injury to persons:

    

●  

Close supervision is necessary when this product is used by, on, or near children or invalids.

    

●  

Use this product only for its intended use as described in this manual.

      Do not use attachments not recommended by the manufacturer.

    

● 

 Never operate this product if it has a damaged cord or plug, if it is not  working properly,  

       has been dropped or damaged, or dipped into water.

      Return the product to a service center for examination and repair.

    

●  

Keep the cord away from heated surfaces.

    

●  

Never drop or insert any object into any opening or hose.

    

●  

Do not use outdoors or operate where aerosol (spray) products are  being used or where oxygen 

       is being administered.

    

●  

Connect this product to a properly grounded outlet only. See   grounding instructions.

    

●  

Unplug this product before filling. Fill (reservoir) with water only.

Optional Grounding Instructions

GROUNDING

User’s Guide

ver.1707

BIOBIDET SLIM 1

 (120V, 60Hz)

Summary of Contents for SLIM 1









Reviews: