bintec elmeg bintec 4Ge-LE Installation Manual Download | Manualshive

Page: 20 / 32

background image

• Place the router as shown in the figure above.

• To insert the SIM card, follow the instructions shown on the bintec 4Ge-LE.

• Press it until it is fully inserted.

• To extract it, press it again and remove it.

3 Components and Power Supply

bintec elmeg

16

bintec 4Ge-LE

«
...
18
19
20
21
22
...
»

Summary of Contents for bintec 4Ge-LE

































Reviews:

No comments

Related manuals for bintec 4Ge-LE

Brand: D-Link Pages: 15

DSN-4100 Series

Brand: D-Link Pages: 2

Brand: D-Link Pages: 2

Netlink FRX8000

Brand: Cabletron Systems Pages: 94

MMAC-Plus 9E423-24

Brand: Cabletron Systems Pages: 10

MMAC-Plus 9A128-01

Brand: Cabletron Systems Pages: 22

Spectrum EMM-E6

Brand: Cabletron Systems Pages: 2

SmartSTACK ELS100-24TXG

Brand: Cabletron Systems Pages: 112

Brand: Cabletron Systems Pages: 86

Brand: Cabletron Systems Pages: 54

Cabletron BRIM-F6

Brand: Cabletron Systems Pages: 43

Netlink FRX4000

Brand: Cabletron Systems Pages: 60

CSX200 CyberSWITCH

Brand: Cabletron Systems Pages: 2

Brand: Cabletron Systems Pages: 8

Brand: Cabletron Systems Pages: 4

Brand: Patton electronics Pages: 2

ipRocketLink 3086FR

Brand: Patton electronics Pages: 6

Brand: Patton electronics Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands