Binatone Trend 3 Executive User Manual Download Page 13

1

3

“The phone does

Make sure you're using the 

telephone line cable that 

not ring”

supplied with your Trend 3 Executive.  Other telephone

line cables might not work.
Check that the 

total REN value

 of all equipment 

connected to your telephone line is not more than 4. 

Disconnect one or more telephones.

The Caller Display

feature isn't

Binatone Help Line - 0845 345 9677

     

Calls are charged at Local Call rate.

ALWAYS check 

„

 you have followed the steps listed 

o

n Section 2 to

first that: 

install and set up your Trend 3 

Executive.

„

 

all connectors are firmly inserted in their sockets

.

Everyday use

“I cannot make or 

Make sure you're using the 

telephone line cable that

answer calls.” 

supplied with your Trend 3 Executive.  Other telephone 

line cables might not work.

„

 

the batteries are correctly and securely installed, 

and are not run down

.

working

You need to subscribe

 to the Caller Display service

from your network service provider. Contact the local 

network service provider for details on how to subscribe.
The caller may have 

withheld

 their number by dialing

141. Or they may be calling from a network that does

not transmit the caller's number (e.g. it may be an 

international call.)

ERROR message 

is displayed

ERROR 

appears in the display if the unit detects

anything other than valid Caller Display information 

during silent period after the first ring. This message 

indicates either the presence of noise on the line, or 

that an invalid message has been sent from the network

service provider.
Be sure to wait until the second ring before answering.

The 

Trend 3 Executive

 must be serviced by trained engineers.

 NEVER 

attempt 

any repairs or adjustments yourself - you could make

 the problem 

worse and invalidate the 

g

uarantee.

!

8. Troubleshooting

Summary of Contents for Trend 3 Executive


















Reviews: