BIMG METVISA FG3D Instruction Manual Download Page 17 | Manualshive

Page: 17 / 22

BIMG METVISA FG3D Instruction Manual Download Page 17

17

Difficulty adjusting the
flame

Damaged or broken pressure
regulator (register).

Send equipment to the nearest authorized service
station or contact the factory, as there are risks of
accidents.

Damaged or broken pressure
regulator (register).

Send equipment to the nearest authorized service
station or contact the factory.

Lack of gas during
operation

Lack of gas.

Check if there is gas in the cylinder, if the gas cylinder
register is open, if the gas hose is connected and if
the gas regulator is open.

Damaged or broken pressure
regulator (register).

Send equipment to the nearest authorized service
station or contact the factory, as there are risks of
accidents.

Equipment with a
burning or smoke smell.

The oil has lost its ideal
characteristics for frying.

It  is  recommended  not  to  use  the  same  oil  for  many
operating  cycles.  Check  some  instructions  from
ANVISA  (National  Health  Surveillance  Agency)  on
page 14.

For more information and clarification, contact the Authorized Technical Assistance nearest

you. See list of technical assistance on our website:

www.metvisa.com.br

«
...
15
16
17
18
19
...
»

Summary of Contents for METVISA FG3D























Reviews:

No comments