BILTON International GmbH
Lofererstrasse 23
5760 Saalfelden / Austria
Tel.: +43 6582 71164
Fax.: +43 6582 71164-999
office@biltongroupcom
www.biltongroup.com
III
IP20
AUSTRIA
Original Instruction Manual
LED-Driver
E
170807 LED Power Supply BILTON PSU 60
170806 LED Power Supply BILTON PSU 100
quantity
1
BILTON LED-Driver
1
Orginal Instruction Manual
CONTENT
DESIGNATED USE
The LED driver feeds LED luminaires LED modules. They are
suitable:
// For the connection to power grids (AC input) and the DC output
of devices which are compatible with the electrical characteri-
stics of the power supply.
// For indoor use only.
// For service in compliance with the technical data.
The following restrictions apply:
// Never use the power supply for life-saving or life-sustaining
equipment.
// Never use outdoors.
// Never immerse in water or other fluids.
// Dry location use only.
// Protect from spray water.
// Avoid the following ambient conditions:
/ High humidity with risk of water condensation.
/ Permanent vibrations.
/ Strong temperature fluctuations.
CONNECTION OF LED-DRIVER
The connection may occur exclusively through an electrician /
electric expert.
AC input (mains supply):
Power leads min 2x1mm², insert stripped litz wires into terminal
“PRI” 220-240V~
DC output:
Detailed information you will find in the datasheet for each unit.
FOR YOUR SAFETY
SEC
+ / -
LED connection
Read instruction manual
This manual contains information for the safe handling of those
LED drivers / control units which are listed on the front page. It
explains the installation of the mains (AC) and secondary (DC)
adapters.
// Always read the instruction manual first before using the power
supply.
// The instruction manual is part of the product and should always
be at hand.
// The Illustrations in this instruction manualmay differ from the
actual look of the power supply.
Prevent shock-hazard
// Never use a power supply with damagedhousing or cable.
// Never modify a power supply or open itshousing.
// Connect the power supply to a regularinstalled outlet only.
// Protect connectors from moisture.
Prevent property damage
// Never carry the power supply by it selectrical cable or pull at
the cable.
// For separating the connection always pull on the plug, never
on the cable.
// Cables must be installed safely to avoid tripping over.
// Disconnect the power supply during thunderstorms.
NOTICE
Reversed polarity (plus and minus) can damage the connected
LEDs!
// Double check the polarity before switch-on
In order to solve the connection push down the terminal careful-
ly with a screw driver and pull out the leads.
MAINTENANCE AND TROUBLESHOOTING
WARNING
Risk of lethal electric shock if fluid leaks into the power supply!
// Disconnect power supply before cleaning.
// Do not use fluids for cleaning.
// Wipe with a dry cloth only.
Do not use chemical cleaning agents. The power supply is
maintenance-free. In case of a faulty power supply or malfunc-
tions that cannot be solved, please contact BILTON.
DISPOSAL
Environmental contamination caused by incorrect disposal!
// Dispose the unit via the designated take-back system.
TECHNICAL DATA
General
Service temperature
-20 … +45 °C
Storage temperature
-40 … +70 °C
Humidity
<95 %, non- condensing
Protection rating
IP20
Protection class
II
Electrically
See printing on power supply
Imprint:
BILTON International GmbH // Lofererstrasse 23 //5760 Saalfelden // Austria // +43 6582 71164 // +43 6582 71164-999 // [email protected] //
www.biltongroup.com / Version: January 2018, Errors and omissions excepted.
Original Instruction Manual
LED-Driver
E
LED POWER SUPPLY BILTON PSU 60
LED POWER SUPPLY BILTON PSU 100
quantity
1
BILTON LED-Driver
1
Orginal Instruction Manual
CONTENT
DESIGNATED USE
The LED driver feeds LED luminaires LED modules. They are
suitable:
// For the connection to power grids (AC input) and the DC output of
devices which are compatible with the electrical characteristics
of the power supply. (http://www.biltongroup.com/downloads/).
// For indoor use only.
// For service in compliance with the technical data.
The following restrictions apply:
// Never use the power supply for life-saving or life-sustaining
equipment.
// Never use outdoors.
// Never immerse in water or other fluids.
// Dry location use only.
// Protect from spray water.
// Avoid the following ambient conditions:
/ High humidity with risk of water condensation.
/ Permanent vibrations.
/ Strong temperature fluctuations.
CONNECTION OF LED-DRIVER
The connection may occur exclusively through an electrician /
electric expert.
AC input (mains supply):
Power leads min 2x1mm², insert stripped litz wires into terminal
“PRI” 220-240V~
DC output:
Detailed information you will find in the datasheet for each unit.
FOR YOUR SAFETY
SEC
+ / -
LED connection
Read instruction manual
This manual contains information for the safe handling of those
LED drivers / control units which are listed on the front page. It
explains the installation of the mains (AC) and secondary (DC)
adapters.
// Always read the instruction manual first before using the power
supply.
// The instruction manual is part of the product and should always
be at hand.
// The Illustrations in this instruction manualmay di er from the
actual look of the power supply.
Prevent shock-hazard
// Never use a power supply with damagedhousing or cable.
// Never modify a power supply or open itshousing.
// Connect the power supply to a regularinstalled outlet only.
// Protect connectors from moisture.
Prevent property damage
// Never carry the power supply by it selectrical cable or pull at
the cable.
// For separating the connection always pull on the plug, never on
the cable.
// Cables must be installed safely to avoid tripping over.
// Disconnect the power supply during thunderstorms.
NOTICE
Reversed polarity (plus and minus) can damage the connected
LEDs!
/ Double check the polarity before switch-on
In order to solve the connection push down the terminal carefully
with a screw driver and pull out the leads.
MAINTENANCE AND TROUBLESHOOTING
WARNING
Risk of lethal electric shock if fluid leaks into the power supply!
// Disconnect power supply before cleaning.
// Do not use fluids for cleaning.
// Wipe with a dry cloth only.
Do not use chemical cleaning agents. The power supply is main
-
tenance-free. In case of a faulty power supply or malfunctions
that cannot be solved, please contact BILTON.
DISPOSAL
Environmental contamination caused by incorrect disposal!
// Cut o
le of the power supply and dispose the unit via
the designated take-back system.
TECHNICAL DATA
IP20
AUSTRIA
General
Service temperature
-20 … +45 °C
Storage temperature
-40 … +70 °C
Humidity
<95 %, non- condensing
Protection rating
IP20
Protection class
II
Electrically
See printing on power supply
BILTON International GmbH
Lofererstrasse 23
5760 Saalfelden / Austria
Tel.: +43 6582 71164
Fax.: +43 6582 71164-10
www.BILTON.at
Imprint:
BILTON International GmbH // Lofererstrasse 23 //5760 Saalfelden // Austria // +43 6582 71164 // +43 6582 71164-10 // [email protected] // www.BILTON.at
Version: July 2016, Errors and omissions excepted.