Part No. 890313 Form No. F010396D
Page 12 of 12
Will not vacuum or has poor vacuum perfor-
mance.
Poor chipping performance.
PARTS LIST CONTINUED
( Continued from page 11 )
78
79
80
81
82
83
CONNECTOR BAG QUICK
890176
1
890176
1
84
LABEL READ OWNER'S MANUAL
890301
1
890301
1
85
TAMPER
890229
1
890229
1
86
LABEL EAR EYE BREATHING
890254
1
890254
1
87
PLATE BRACE ADJ. KD / TKD
900756
1
900756
1
Description
Item
No.
Part No.
TKD505H
QTY
QTY
Part No.
TKD505ICQ
T R
T R
T R
T R
T RO U B L E S H O O
O U B L E S H O O
O U B L E S H O O
O U B L E S H O O
O U B L E S H O OTING
TING
TING
TING
TING
Before Requesting Service Review These Suggestions
Engine stalls or labors when chipping.
Feed branches at a slower rate. Service engine.
Solution
Solution
Solution
Solution
Solution
Possible Cause
Possible Cause
Possible Cause
Possible Cause
Possible Cause
Problem
Problem
Problem
Problem
Problem
Nozzle scrapes ground in lowest height
setting.
Abnormal vibration.
Engine will not start.
Engine is locked, will not
pull over.
Debris locked in chipper blade, hopper or inside
impeller. Engine problem.
Check stop switches, throttle, choke position and
gasoline. Connect spark plug wire. Clean or replace
air cleaner. Or contact a qualified service person.
See page 5, Clearing a clogged chipper hopper.
Contact an engine servicing dealer for engine
problems.
Check impeller and replace if required. Check
Engine.
Adjust nozzle height. (See Nozzle height fine
adjustment for hard surface use on page 5).
Avoid extremely hard wood. Sharpen or replace
chipper blade (see page 8).
Clean debris bag. Shake bag clean or wash. Adjust
nozzle height. Check for hose kit cap. Unclog nozzle or
exhaust (see page 5). Allow air to feed with debris.
Dirty debris bag. Nozzle height set too high or too low.
Hose kit cap missing. Clogged nozzle or exhaust.
Excessive quantity of debris.
Extremely hard wood. Dull or damaged chipper blade.
Feeding branches into chipper too rapidly.
Engine
service may be required.
Nozzle height out of adjustment.
Loose or out of balance impeller or loose engine.
Stop switch off (Honda only). Throttle in off position.
Engine not in full choke position (Honda only). Out of
gasoline. Bad or old gasoline. Spark Plug wire
disconnected. Dirty air cleaner.
19
19
19
19
19
20
20
20
20
20
* Denotes
standard
hardware item
that may be
purchased
locally.
Engine Service and Warranty
Contact your nearest engine manufacturer's autho-
rized servicing dealer.
22.1
22.1
22.1
22.1
22.1
22
22
22
22
22
BILLY GOAT INDUSTRIES INC.
P.O. BOX 308 (1803 S JEFFERSON) LEE'S SUMMIT, MO 64063 / USA
PHONE: 816-524-9666 FAX: 816-524-6983
WARRANTY PROCEDURE
Please fill in the WARRANTY CARD and send the upper part to Billy Goat.
The WARRANTY terms are stated on the lower part which remains with the
user. Whenever a Billy Goat Machine is faulty due to a defect in material
and / or workmanship, the owner should make a warranty claim as follows:
The Machine should be taken to the dealer from whom it was
purchased or to an authorized Billy Goat dealer.
The owner should present the remaining half of the Warranty
Registration Card, or, if this is not available, the invoice or receipt.
The Warranty Claim will be filled in by the authorized Billy Goat Dealer,
who will send it with the faulty part to Billy Goat headquarters.
The Quality / Service department at Billy Goat headquarters will study
the claim and parts and will notify their conclusions.
The decision by the Quality / Service department at Billy Goat
headquarters to approve or reject a Warranty claim is final and
binding.
Note: To process a Warranty Claim, it is necessary to quote the Model
& Serial number who are printed on the Billy Goat Serial Plate.
Purchased
from
Purchase
Date
21
21
21
21
21
Serial Plate
R
ecord your machine model, serial number
and date-of-purchase and where purchased
R
min
-1
Operator
1803 S. Jefferson
P.O. Box 308
Lee's Summit,
MO 64063 / USA
Tel (816) 524-9666
Fax (816) 524-6983
Model
Serial No.
Unit(Weight)
Engine Power
lbs.
kg
kW
rpm
L
A
p
108
98
L
A
