background image

                       GRAZOR Owner’s Manual

          

Part No 610502 

 

610502_-_HI 

 

PACKING CHECKLIST

 

 

Your Billy Goat is shipped from the factory in one carton, completely assembled except for the upper handle assembly, lower 

handles, handle brace, brush lift rod, and brush.

 

 

  

PUT OIL IN ENGINE BEFORE STARTING 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

ASSEMBLY

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

READ 

all safety instructions before assembling unit. 

 

TAKE CAUTION

 when removing the unit from the box. 

1. 

Install the lower handles one on each side of the unit using bolt (item 45), washer (item 54) and nut (item 52). There are two 

bolts per lower handle section. 

NOTE:

 The lower handle has a left and right hand section. Be sure when installing that each 

section will point to the outside of the unit when hardware is secured.

 

2

. Install upper handle assembly by aligning the holes in the upper handle with the holes in the lower handle stubs that are 

preassembled on the machine. Secure the handles together using bolt (Item 46), washer (Item 54), and nut (Item 52) on the 

operator’s right hand side. Secure using bolt (Item 64), washer (Item 54), and nut (Item 52) on the operator’s left hand side. 

Use the same hardware to secure the flat end of the handle brace (Item 42) to the left side of the handle.

 

3.

 Secure the bent end of the handle brace (Item 42) to the face of the engine using bolt (Item 47). 

4.

 Install the brush lift rod (Item 38) by placing one end through the hole in the lift control arm mounted on the upper handle and 

securing it with a washer (Item 54) and pin (Item 60). Place the other end though the brush pivot arm and secure in the same 

way.  

NOTE:

 The pin and washer come pre-installed in the ends of the rod (Item 38).  Remove and re-use them for final 

assembly. 

5.

 Install brush (Item 6) by removing the brush guard (Item 27) and removing the brush mounting nut (Item 15) and one washer 

(Item 16). Slide the brush on the shaft and reinstall the washer, nut, and brush guard. 

Boxing Parts 

Checklist

 

 

 

 

Handle upper 

assembly 610438-S 

 

 

Handle Brace 

610442 

 

 

Brush Lift Rod 

610426 

 

 

Handle Lower RH 

610423 

 

 

Handle Lower LH 

610424 

 

 

Brush 8” Wire 

610140

 

 

 

Owner’s Manual GZ 

610502

 

Engine Manual  

 

 

Briggs and Stratton 

 

 

PARTS BAG & LITERATURE ASSY  

 

Warranty card P/N- 400972, Owner’s Manual P/N-610502, General Safety and Warnings manual P/N-100296. 

Parts Bag 

Checklist

 

 

 

Safety Glasses 

610129 qty. 1

 

12

NOT 

FOR 

REPRODUCTION

Summary of Contents for GRAZOR GZ551V











Reviews: