manualshive.com logo in svg

Billet Specialties Tru Trac # 13805, Installation Manual, Page: 8 / 11

Share
Download
Billet Specialties Tru Trac # 13805 Installation Manual Download Page 8

www.billetspecialties.com

www.billetspecialties.com

15

FOR kITS WITHOUT POWER STEERING – CONTINUE TO FIGURE 11

Figure 10: Install Power Steering Pump With Pulley

Apply anti-seize to the threads of the two 5/16-18 x 2-3/4” socket head 
cap screws.

Place power steering pump with pulley on bracket and align. 

Thread the two 5/16-18 x 2-3/4” cap screws with 5/16” lock washers 
through the power steering pump mount bosses and into the power 

steering bracket, tighten firmly 26ft/lbs.

Figure 9: Install Alternator

Apply anti-seize to the 8mm-1.25 x 25mm ARP 12-point cap screw and the 
10mm-1.25 x 70mm ARP 12-point cap screw. 

A]

 Place alternator between bridge bracket and alternator bracket, align 

alternator bosses with the bridge bracket. Thread the 10mm ARP 12-point 
cap screw through the bottom bridge bracket hole and alternator into 

the alternator bracket, finger tighten. 

B]

 Thread the 8mm ARP 12-point cap screw through the bridge bracket 

and into the top alternator boss.

Tighten all fasteners firmly at this time: All ARP 12-point fasteners and flat 

head bridge bracket screws.

A

B

Summary of Contents for Tru Trac # 13805












Reviews:

No comments