5
01-2016A
PLEASE READ THIS MANUAL IN ITS ENTIRETY PRIOR TO USING THIS PRODUCT!
PLEASE READ THIS MANUAL IN ITS ENTIRETY PRIOR TO USING THIS PRODUCT!
PLEASE READ THIS MANUAL
IN ITS ENTIRETY
PRIOR T
O USING THIS PRODUCT!
PLEASE READ THIS MANUAL
IN ITS ENTIRETY
PRIOR T
O USING THIS PRODUCT!
BIG DOG TREESTANDS BIG RAMPAGE ASSEMBLY
FIGURE 2
PLATFORM/SEAT/
SHOOTING RAIL
ASSEMBLY
FIGURE 3
LADDER AND
CROSS TUBE
ASSEMBLY
D
G
J
M
N
C
C
I
L
O
K
H
(
a
)
(
a
)
(
b
)
P
STEP 1: Locate the left/right foot platform (L&M) (refer to Figure 1). Bolt them together as shown in Figure 2 using
two (2) 8mm x 2” bolts and locknuts. Locate the sub-frame (N) (refer to Figure 1). Bolt it to the assembled platforms
as shown in Figure 2 using four (4) 8mm x 2” bolts and locknuts. Locate the foot rest (K) and Z connection tubes
(J) (refer to Figure 1). Install them with assembled platforms as shown in Figure 2 using two (2) 8mm x 3” bolts and
locknuts with (1) nylon washer between the foot rest and foot platform tube ends on both sides.
STEP 2: Locate the seat support tubes (G) (refer to Figure 1). Install them to the Z connection tubes (J) as shown in
Figure 2 using two (2) 6mm x 1-3/8” bolts and locknuts with four (4) 6mm metal washers. Locate the V-bar (H) (refer
to Figure 1). Install it to the seat support tubes (G) as shown in Figure 3 using two (2) 8mm x 3” bolts and locknuts.
Note: Teeth plate on the welded V-bar shall be facing toward foot platform.
STEP 3: Locate the platform support braces (I) (refer to Figure 1). Bolt them to the back side of the foot platforms as
shown in Figure 2&3 using four (4) 6mm x 2” bolts and locknuts. Bolt the platform support brace to the seat support
tubes (G) as shown in Figure 3 using one (1) 6mm x 2-1/8” bolt and locknut and repeat on the 2nd platform support
brace. Locate the arm rests (C) and adjustable shooting rail sleeves (D)(refer to Figure 1), insert the adjustable
shooting rail sleeve to the front of the arm rest which has the 2nd hole in the arm rest lower than other side. Bolt
the arm rests (C) to the outside of seat support tubes (G) as shown in Figure 2&3, using (2) 6mm x 2” bolts and
locknuts, repeat on other side.
STEP 4: Locate the seat tubes (E), front seat support tube (F), mesh seat with (2) plastic tubes (B), and four (4)
thick plastic washers. Install mesh seat with (2) plastic tubes (B) to seat tubes (E) as shown in Figure 4. Using
one (1) 8mm x 2-1/8” bolt and locknut on each side, bolt the seat tubes (E) to the front seat support tube (F) with
two (2) thick plastic washers on each side between the seat tubes (E) and front seat support tube (F) as shown in
Figure 4. Locate the shooting rail assembly (A) (refer to figure 1). Insert the shooting rail sections (a) to the middle
section (b) on each side as shown in Figure 3 bolt together using two (2) 6mm x 1-1/8” bolts and locknuts. Locate
the assembled mesh seat containing parts (B,E&F) and bolted shooting rail assembly (A). Install them to the arm
rests as shown in Figure 2 using two (2) 6mm x 3-1/2” bolts, six (6) thick plastic washers and two (2) 6mm locknuts.
(Bolt Stack: shooting rail →thick plastic washer → arm rest (top hole) → two (2) thick plastic washers → seat tube).
FIGURE 4
MESH SEAT
ASSEMBLY
F
B
E
Two Thick Plastic
washer
STEP 5: Locate the top ladder section (P) (refer to Figure 1), Note: the top ladder section has a set of pre-drilled holes below
the top ladder rung. Install it to the Z connection tubes as shown in Figure 3 using two (2) 6mm x 1-3/8” bolts and locknuts with
four (4) 6mm metal washers. Important: All bolts must be loose to install top ladder section.
STEP 6: Locate the cross bars (O) (refer to Figure 1), install them as shown in Figure 3 to the outside of top ladder (P) using
Note: Do NOT tighten any nuts/bolts until product is fully assembled. You will need two (2) 13mm wrenches and two
(2) 10mm wrenches to tighten the assembly (not provided).
