background image

10 

 

      Limited Warranty   

 
 
 

 

This product carries

 the following guarantee against manufacturing defects:   

* Frame is warranted for 2 years from the date of purchase.     

* Components are warranted for 1 year. 

* Warranty is only valid for the original purchaser. 
* Labor and freight charges are not included. 
* Normal wear, neglect, abuse, accidents, improper assembly or maintenance, or the 

installation of parts or accessories not compatible with the original intended use 
of the bike, as sold, are not covered by the warranty. 

* Neither does it cover any corrosion caused by failure to clean the bikes on regular 

basis.   

* This warranty is limited to the repair or replacement of the defective part at no 

cost. 

The supplier

 shall in no event be responsible for consequential, special 

damages, and any parts failures, breakages or injuries resulting from misuse of 
the machine or failure to follow the recommended maintenance procedures. 

* Warranty claims must be through an authorized dealer, and replacement parts will 

normally be dispatched to you. We recommend you held a small stock of basis 
spare parts, as well as a tool kit to cover the regular maintenance routines. 

* The Limited Warranty is the only express or implied warranty   
    applicable to 

original supplier

. Any implied warranties, including warranties of 

merchantability and fitness shall be limited in scope and duration in accordance 
with this limited warranty. 

 

 
 
 
 
 
 
 
 
 
 
 
 

Summary of Contents for SPRINT BIKE TWO H918A-1













Reviews: